Modulating oxidation state of Ni/CeO 2 catalyst for steam methane reforming: a theoretical prediction with experimental verification

Chan Wu,Zhourong Xiao,Li Wang,Guozhu Li,Xiangwen Zhang,Lichang Wang

DOI: https://doi.org/10.1039/d0cy02197k

2021-01-01

Abstract:Rational design of partially oxidized Ni/CeO 2 with both high activity and good stability by DFT for efficient methane steam reforming.

chemistry, physical

What problem does this paper attempt to address?

Modulating Oxidation State of Ni/CeO2 Catalyst for Steam Methane Reforming: a Theoretical Prediction with Experimental Verification

Chan Wu

DOI: https://doi.org/10.1039/d0cy02197k

IF: 6.177

2021-01-01

Catalysis Science & Technology

Abstract:Rational design of partially oxidized Ni/CeO2 with both high activity and good stability by DFT for efficient methane steam reforming.
CO and Methane Oxidation Over CeXZr1-XO2 Mixed Oxide Supported PdO Catalysts

Lei Ma,Meng-Fei Luo,Li-Feng Han,Song-Ying Chen

DOI: https://doi.org/10.1023/A:1010313605332

2000-01-01

Reaction Kinetics and Catalysis Letters

Abstract:In this paper, the Ce X Zr 1-X O 2 -supported PdO catalysts were prepared and the effect of Ce/Zr ratio on catalytic activity for CO and methane oxidation was studied, both activity and the reduction behavior of catalyst depend on the Ce/Zr ratio. The reduction behavior of those catalysts was characterized by means of TPR.
Methanol steam reforming over Ni-CeO2 model and powder catalysts: Pathways to high stability and selectivity for H2/CO2 production

Zongyuan Liu,Siyu Yao,Aaron Johnston-Peck,Wenqian Xu,José A. Rodriguez,Sanjaya D. Senanayake

DOI: https://doi.org/10.1016/j.cattod.2017.08.041

IF: 5.3

2018-08-01

Catalysis Today

Abstract:Nickel-ceria has been reported as a very good catalysts for the reforming of methane. Here, the methanol steam reforming reaction on both powder (Ni-CeO2) and model (Ni-CeO2-x(111)) catalysts was investigated. The active phase evolution and surface species transformation on powder catalysts were studied via in situ X-ray diffraction (XRD) and diffuse reflectance infrared transform spectroscopy (DRIFTS). Phase transitions of NiO → NiC → Ni and CeO2 → CeO2-x were observed during the reaction. The simultaneous production of H2/CO2 demonstrates that the active phase of the catalysts contains metallic Ni supported over partially reduced ceria. The DRIFTS experiments indicate that a methoxy to formate transition is associated with the reduction of ceria whereas the formation of carbonate species results from the presence of metallic Ni. A study of the reaction of methanol with Ni-CeO2-x(111) by X-ray photoelectron spectroscopy (XPS) points to the essential role of metal-support interactions in an oxygen transfer from ceria to Ni that contributes to the high selectivity of the catalysts.

chemistry, physical,engineering, chemical, applied
Oxygen Vacancy Induced Strong Metal-Support Interactions on Ni/Ce0.8Zr0.2O2 Nanorod Catalysts for Promoting Steam Reforming of Toluene: Experimental and Computational Studies.

Zezhi Chen,Lu Chen,Huijuan Gong,Huiqiang Yu,Xiaoshu Wang,Feng Lin

DOI: https://doi.org/10.1021/acs.langmuir.3c00195

IF: 3.9

2023-03-16

Langmuir

Abstract:To develop an efficient Ni-based steam reforming catalyst for tar removal from the products of biomass gasification, Ni/Ce0.8Zr0.2O2 nanorods were designed. The Ni/Ce0.8Zr0.2O2 nanorod was used as a catalyst in steam reforming of toluene, which was regarded as a model compound of biomass gasification tar. At gas hourly space velocity (GHSV) of 24,000 h-1 and Ni loading of 5 wt %, the 5Ni/Ce0.8Zr0.2O2 nanorod catalyst achieved 100% of toluene conversion at 600 °C. After 10 h of operation, toluene conversion still reached 87.6%, and the carbon deposition rate was only 1.9 mg/gcat h-1. The experimental results demonstrated that the 5Ni/Ce0.8Zr0.2O2 nanorod catalyst showed much higher catalytic activity and coking resistance than other Ni-based catalysts reported in the literature. Through different characterization technologies and density functional theory calculations, it was confirmed that the excellent catalytic performance was attributed to the strong metal-support interaction (SMSI) between Ni and the {100} facet of Ce0.8Zr0.2O2. The special surface structure of {100} allowed Ni atoms to anchor to the surface oxygen vacancies and maintained its reduced state by electron transport between surface atoms. The anchored Ni facilitated oxygen vacancies formation and H2O dissociation on the support, while the support modulated the electronic structure of Ni, which promoted its ability to toluene activation.

Engineering,Environmental Science,Chemistry,Medicine
Dynamics of the Cu/CeO2 Catalyst during Methanol Steam Reforming

Shiqing Jin,Didi Li,Zhen Wang,Yiming Wang,Li Sun,Minghui Zhu

DOI: https://doi.org/10.1039/d2cy01514e

2022-10-14

Abstract:Supported Cu/CeO2 catalysts with various loadings prepared by a deposition-precipitation method are thoroughly investigated with a series of in situ characterization techniques. The catalyst surface contains metallic Cu0 and interfacial sites, with the latter acting as active sites for the methanol steam reforming reaction. Moreover, the structures of both types of sites dynamically change in response to various environmental conditions.

chemistry, physical
Rational design of nickel-based catalyst coupling with combined methane reforming to steadily produce syngas

Qinhong Wei,Xinhua Gao,Luhui Wang,Qingxiang Ma

DOI: https://doi.org/10.1016/j.fuel.2020.117631

IF: 7.4

2020-07-01

Fuel

Abstract:Inhibiting the aggregation of Ni particles and coke deposition on supported nickel catalysts has always been an enormous challenge in methane reforming to syngas. To address the problem, in this study, a Ce-Al-O supported Ni mesoporous catalyst (Ni/Ce-Al-O-A) was designed and synthesized by using evaporation-induced self-assembly (EISA) method and citric acid auto-reduction (AR) method, respectively. The prepared Ni/Ce-Al-O-A catalyst, without further reduction, was used for combined methane dry reforming comprising CO2 dry reforming of methane (DRM) and methane partial oxidation (MPO) to effectively produce syngas. Employing citric acid auto-reduction method for catalyst preparation directly led to the formation of metallic Ni by calcining the precursor of Ni/Ce-Al-O-A in argon atmosphere, with high dispersion and small particle size (at around 4.5 nm) of metallic Ni being obtained. The Ni/Ce-Al-O-A catalyst presented high catalytic activity, better than those of reference catalyst prepared by general impregnation method and the commercial alumina supported Ni catalyst synthesized by citric acid auto-reduction method. In a 250 h lifetime test, the Ni/Ce-Al-O-A catalyst exhibited an extremely catalytic stability and anti-coking ability, and no deactivation was observed. The excellent catalytic activity of Ni/Ce-Al-O-A catalyst was mainly attributed to the Ce-incorporated Ce-Al-O that facilitated the adsorption and activation of CO2 as well as the combined methane reforming (DRM-MPO) in which the existing oxygen could effectively inhibit the coke formation.

energy & fuels,engineering, chemical
Ni/CeO2 Catalyst Prepared via Microimpinging Stream Reactor with High Catalytic Performance for CO2 Dry Reforming Methane

Yadong Wang,Qing Hu,Ximing Wang,Yanpeng Huang,Yuanhao Wang,Fenghuan Wang

DOI: https://doi.org/10.3390/catal12060606

IF: 3.9

2022-06-02

Catalysts

Abstract:Methane reforming with carbon dioxide (DRM) is one promising way to achieve carbon neutrality and convert methane to syngas for high-value chemical production. Catalyst development with better performance is the key to its potential large-scale industrial application due to its deactivation caused by carbon deposition and metal sintering. Hence, a Ni/CeO2 catalyst (Ni/CeO2-M) with higher CO2 conversion and better stability is prepared, supported on CeO2 precipitated via a novel microimpinging stream reactor. A series of ex-situ or in-situ characterizations, such as CO titration measurements, two-step transient surface reaction (two-step TSR), CO2 and CH4 temperature-programmed surface reaction (CO2-TPSR and CH4-TPSR), X-ray absorption fine structure (XAFS), and in-situ Raman spectroscopy study, were used to investigate its structure and mechanism. In contrast to Ni supported on commercial CeO2 (Ni/CeO2-C), the Ni/CeO2-M catalyst with stronger lattice oxygen mobility and higher oxygen storage capacity enhances its CO2 activation ability and carbon deposition. The Ni particle size of the Ni/CeO2-M catalyst decreased, and a higher oxidation state was obtained due to the strong metal–support interaction. Besides the reaction performance improvement of the Ni/CeO2-M catalyst, the novel microimpinging stream reactor could achieve catalyst continuous production with a high preparation efficiency. This work provides a novel method for the high-performance catalyst preparation for DRM reaction and its mechanism study gives a deep insight into high-performance catalyst development via bottom-up study.

chemistry, physical
Ni/Ce0.9Eu0.1O1.95 with enhanced coke resistance for dry reforming of methane

Yaning Wang,Rongjun Zhang,Binhang Yan

DOI: https://doi.org/10.1016/j.jcat.2022.01.020

IF: 7.3

2022-03-01

Journal of Catalysis

Abstract:Methane reforming with carbon dioxide provides an environmentally friendly route for converting methane to synthesis gas while consuming two greenhouse gases. Large-scale implementation of this process has been stalled by the lack of stable catalysts owing to the rapid deactivation caused by carbon deposition and sintering. Ni/Ce0.9Eu0.1O1.95 catalysts with better activity and enhanced stability are synthesized for dry reforming of methane. This reaction is believed to occur via the direct C-H bond dissociation of CH4 to form surface carbon intermediates on metal sites followed by the oxidation of carbon intermediates to CO. Compared with CeO2, Ce0.9Eu0.1O1.95 with stronger lattice oxygen mobility and higher oxygen storage capacity generates more mobile active oxygen species that participate in eliminating the carbon deposition. Moreover, the particle size of Ni species decreases and Ni shifts to higher oxidation state as a result of the strong metal-support interaction over Ce0.9Eu0.1O1.95. The more surface oxygen species are involved in the reaction, the more methane can be converted to CO rather than surface carbon. As a consequence, the balance between the rate of carbon generation (i.e., the direct C-H bond dissociation of CH4) and the rate of carbon consumption (i.e., the oxidation of formed carbon intermediates) can be achieved for dry reforming of methane over Ni/Ce0.9Eu0.1O1.95, leading to less coke accumulation and thereafter an improved overall catalytic performance.

chemistry, physical,engineering, chemical
Effect of Ceria Amount on Promoting Ni-Co/SBA-15 Catalyst for n-Dodecane Steam Reforming

Zhourong Xiao,Li Wang,Xiangwen Zhang,Ling Li,Chan Wu,Shuang Ji,Guozhu Liu,Guozhu Li

DOI: https://doi.org/10.1002/slct.201601439

2016-01-01

ChemistrySelect

Abstract:Catalytic steam reforming of long-chain hydrocarbons has drawn great attention for hydrogen production, which can be used for on-board/on-site fuel cell. In this study, a series of SBA15 supported Ni-Co bi-metal catalysts with different ceria loadings (denoted as NC-xCeO(2)/SBA-15) have been prepared via a facile ethylene-glycol route. Various techniques including XRD, nitrogen adsorption-desorption, H-2-TPR/O-2-TPO, TPH, TEM/SEM, TG/DTG and Raman spectra were employed to characterize the fresh and spent catalysts. Steam reforming of n-dodecane has been carried out to evaluate catalytic perform-ance of the obtained catalysts at high LHSV (24 ml/g(cat).h) and atmospheric pressure in a fixed-bed tubular reactor using the H2O/C ratio of 4. The catalyst with 6wt% CeO2 (NC-6CeO(2)/SBA15) exhibits the best activity and stability. The improvement of performance for n-dodecane steam reforming is ascribed to the strong interaction between metal and ceria, which would control metal growth and prevent metal sintering. In addition, the oxidation of deposited coke on metal has been facilitated by the accompanied ceria promoter via its excellent oxygen storage-release capability.
Enhanced activity and stability of Ce-doped PrCrO3-supported nickel catalyst for dry reforming of methane

Wen Peng,Zongbao Li,Bo Liu,Peng Qiu,Dong Yan,Lichao Jia,Jian Li

DOI: https://doi.org/10.1016/j.seppur.2022.122245

IF: 8.6

2022-12-15

Separation and Purification Technology

Abstract:Dry reforming of methane (DRM) can convert the greenhouse gases to more valuable and easy separated syngas, which is of industrial and environmental importance. However, the reaction suffers from catalyst deactivation arising from the carbon deposition. Herein, we developed a perovskite PrCrO3-δ-supported nickel catalyst with high conversion rates of CH4 (∼89 %) and CO2 (∼88 %), as well as excellent stability (>110 h) by a few Ce doping. The results demonstrated that surface oxygen vacancies played a crucial role in coking resistance. The prepared Ni@Pr1-xCexCrO3 has proven effective in converting the carbon rapidly into CO to suppress carbon deposition, improving the stability of the catalyst. This strategy provides a potential solution for the efficient conversion of the low calorific value fuels.

engineering, chemical
CO2 Reforming of CH4 over Rare Earth Elements Functionalized Mesoporous Ni–Ln (ln = Ce, La, Sm, Pr)–Al–O Composite Oxides

Leilei Xu,Zhichao Miao,Huanling Song,Lingjun Chou

DOI: https://doi.org/10.1016/j.ijhydene.2013.12.077

IF: 7.2

2014-01-01

International Journal of Hydrogen Energy

Abstract:A series of rare earth elements functionalized mesoporous Ni-Ln (Ln = Ce, La, Sm, Pr)-Al -O composite oxides were originally designed and facilely synthesized via one-pot evaporation induced self-assembly (EISA) strategy. These mesoporous materials with outstanding thermal stability were investigated as the catalysts for the CO2 reforming of CH4, performing excellent catalytic activities and long-term catalytic stabilities. The "confinement effect" of the mesoporous framework matrixes contributed to stabilizing the Ni nanoparticles during the process of reaction; therefore, the serious thermal sintering of the Ni nanoparticles under severe reduction and reaction conditions was suppressed to some degree, accounting for the long catalytic stability of these mesoporous catalysts. The modification of the rare earth elements (Ce, La, Sm, Pr) played crucial roles in promoting the catalytic activities and reducing the carbon deposition. Besides, the presence of the rare earth elements also significantly influenced the distribution of the carbon species deposited over the spent catalysts. Hereby, these mesoporous Ni-Ln (Ln = Ce, La, Sm, Pr)-Al-O composite oxides promised a group of novel and stable catalyst candidates for carbon dioxide reforming of methane. Copyright (C) 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.
Bimetallic NiFe Nanoparticles Supported on CeO2 as Catalysts for Methane Steam Reforming

Andrea Braga,Marina Armengol-Profitós,Laia Pascua-Solé,Xavier Vendrell,Lluís Soler,Isabel Serrano,Ignacio J Villar-Garcia,Virginia Pérez-Dieste,Núria J Divins,Jordi Llorca

DOI: https://doi.org/10.1021/acsanm.3c00104

2023-05-02

Abstract:Ni-Fe nanocatalysts supported on CeO2 have been prepared for the catalysis of methane steam reforming (MSR) aiming for coke-resistant noble metal-free catalysts. The catalysts have been synthesized by traditional incipient wetness impregnation as well as dry ball milling, a green and more sustainable preparation method. The impact of the synthesis method on the catalytic performance and the catalysts' nanostructure has been investigated. The influence of Fe addition has been addressed as well. The reducibility and the electronic and crystalline structure of Ni and Ni-Fe mono- and bimetallic catalysts have been characterized by temperature programmed reduction (H2-TPR), in situ synchrotron X-ray diffraction (SXRD), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. Their catalytic activity was tested between 700 and 950 °C at 108 L gcat-1 h-1 and with the reactant flow varying between 54 and 415 L gcat-1 h-1 at 700 °C. Hydrogen production rates of 67 mol gmet-1 h-1 have been achieved. The performance of the ball-milled Fe0.1Ni0.9/CeO2 catalyst was similar to that of Ni/CeO2 at high temperatures, but Raman spectroscopy revealed a higher amount of highly defective carbon on the surface of Ni-Fe nanocatalysts. The reorganization of the surface under MSR of the ball-milled NiFe/CeO2 has been monitored by in situ near-ambient pressure XPS experiments, where a strong reorganization of the Ni-Fe nanoparticles with segregation of Fe toward the surface has been observed. Despite the catalytic activity being lower in the low-temperature regime, Fe addition for the milled nanocatalyst increased the coke resistance and could be an efficient alternative to industrial Ni/Al2O3 catalysts.
Preparing a Zr-Doped CeO 2 Nanorod to Improve the Catalytic Performance of the Ni-Based Catalyst for Dry Reforming of Methane by Enhancing Oxygen Supply

Zongpeng Zou,Tao Zhang,Li Lv,Wenxiang Tang,Guoquan Zhang,Raju Kumar Gupta,Yan Wang,Shengwei Tang

DOI: https://doi.org/10.1021/acssuschemeng.3c00419

IF: 8.4

2023-05-04

ACS Sustainable Chemistry & Engineering

Abstract:Dry reforming of methane (DRM) is a feasible route to realize the resource utilization of greenhouse gases CO2 and CH4. The Ni-based catalyst is recognized as a potential catalyst for the industrialization of DRM. However, catalyst deactivation caused by carbon deposition is a challenge. Providing enough active oxygen species to accelerate the reaction between CH x (x = 0–3) and oxygen species is the key to inhibit coking. Ni-based catalysts loaded on a Zr-doped Ce1–x Zr x O2 nanorod were prepared by a one-step hydrothermal method. Benefiting from lattice distortion caused by Zr doping, the Ni/Ce0.95Zr0.05O2 catalyst showed the best catalytic activity and stability. Compared with the Ni/CeO2 catalyst, the activation energy of CH4 and CO2 decreased by 20 and 22%, respectively. The 100 h stability test showed that the Ni/CeO2 catalyst was 10% deactivated, and the carbon deposition rate was 0.82 mgc·gcat·–1·h–1, while the Ni/Ce0.95Zr0.05O2 catalyst showed excellent stability. The extensive characterization of the catalysts indicated that the enhancement in DRM activity upon Zr doping could be attributed to the increase of oxygen vacancies and the improvement in lattice oxygen mobility. However, excessive Zr doping formed ZrO2 covering oxygen vacancies, resulting in decreased catalytic activity and stability. The results showed that lattice oxygen over the Ni/Ce0.95Zr0.05O2 catalyst not only participated in the oxidation of carbon intermediates but also contributed to the deep dissociation of CH4 over Ni through an oxygen-mediated dissociation pathway. Similarly, the redox cycle on the oxygen vacancies was also important for enhancing the CO2 adsorption activation to relieve the coking of the catalyst.

chemistry, multidisciplinary,engineering, chemical,green & sustainable science & technology
Enhancement of hollow Ni/CeO2-Co3O4 for CO2 methanation: From CO2 adsorption and activation by synergistic effects

Feiyang Hu,Feiyang Hu,Chengkai Jin,Rundong Wu,Claudia Li,Guoqiang Song,Terry Zhi Hao Gani,Kang Hui Lim,Wei Guo,Tianchang Wang,Shunmin Ding,Runping Ye,Zhang-Hui Lu,Gang Feng,Rongbin Zhang,Sibudjing Kawi

DOI: https://doi.org/10.1016/j.cej.2023.142108

IF: 15.1

2023-04-01

Chemical Engineering Journal

Abstract:CO2 absorption and activation play key roles in the process of CO2 methanation, but revealing the mechanism and synergistic effects are still challenges, especially in some complicated routes. Herein, an optimized hollow Ni/CeO2-Co3O4 catalyst is shown to be capable of CO2 absorption and activation, the performance could be attributed to the strong synergistic effects among each component. In addition, the respective role was verified that the Co3O4 and CeO2 contributed to the CO2 adsorption and subsequently coupled with Ni for CO2 activation. Furthermore, in-situ DRIFTS were used to demonstrate the hydrogenation mechanisms, and the promotion of CO2 absorption and CH4 selectivity was confirmed in Ni/CeO2-Co3O4. The DFT results verified the synergistic effects of the established catalysts, which could also be a universal strategy for the catalysts designation.

engineering, chemical, environmental
Fabrication of CeZrO2 on Ni/SiO2 and Promoted Catalysis for Methane Autothermal Reforming in a Fluidized Bed Reactor

Jing Qiangshan,Fang Linxia,Lou Hui,Zheng Xiaoming

DOI: https://doi.org/10.1016/s1002-0721(08)60265-3

IF: 4.632

2009-01-01

Journal of Rare Earths

Abstract:The methane autothermal reforming in the present of oxygen was studied over cerium- and zirconium-promoted Ni/SiO2 catalysts in a fluidized bed reactor. The addition of CeZrO2 resulted in a significant improvement in the initial activity of the catalysis as well as an increase in the stability. The long-term activity of the promoted catalyst was dependent upon the rapid redox properties between the oxidative zone and the reductive zone in a fluidized bed reactor. H2 temperature-programmed reduction (H2-TPR) and temperature-programmed surface reaction (TPSR) studies demonstrated that addition of the CeZrO2 resulted in an increase in the reducibility and oxygen transfer ability of the support, Ni/Ce0.5ZrO0.5O2-SiO2 showed improved redox properties compared with Ni/SiO2 due to a low-temperature reduction. X-ray diffraction (XRD) of the fresh and spent catalysts showed that the promoter enhanced the nickel dispersion and retarded metal particle growth during reaction at high temperature, and surface Ni was gradually oxidized by remaining O2, leading to Ni deactivation.
Unraveling the effects of Ce/Zr molar ratio in mesoporous CexZr1−xO2 on the performance of dry reforming of methane over the supported Ni catalysts

Xiaotian Zhou,Yongzhen Gao,Jingyi Yang,Wenjing Yi,Qingqing Pang,Zhongyi Liu,Baozhong Liu,Meng Zhang

DOI: https://doi.org/10.1016/j.cherd.2023.04.020

IF: 4.119

2023-05-01

Chemical Engineering Research and Design

Abstract:Ni supported on the ordered mesoporous CexZr1−xO2 with various Ce/Zr molar ratios prepared by a programmed evaporation-induced self-assembly method were employed for dry reforming of methane. The systematical techniques, including X-ray diffraction, N2 physisorption, Raman, transmission electron microscope, chemisorption, X-ray photoelectron spectroscopy, diffuse reflection Fourier transform infrared spectrum, thermogravimetric analysis, etc. were used to clarify the structure-activity relationship. It was found that the prepared catalysts all had highly ordered mesoporous structures, and compared to the sole ZrO2 and CeO2, the CeO2-ZrO2 composites exhibited the best thermal stability, stronger basicity, and greater oxygen migration. Especially, the composite with Ce/Zr ratio of 1/4 possessed the suitable basicity and most oxygen vacancies, which were closely related to the excellent anti-carbon ability. Moreover, its supported catalyst had the strongest metal-support interaction and highest Ni dispersion. Expectedly, the catalyst showed the superior activity and the robust stability for at least 1800 min

engineering, chemical
n-Dodecane steam reforming catalyzed by Ni-Ce-Pr catalysts. Part 1: Catalyst preparation and Pr doping

Zhourong Xiao,Shuang Ji,Fang Hou,Yueting Li,Haocui Zhang,Li Wang,Xiangwen Zhang,Guozhu Liu,Ji-Jun Zou,Guozhu Li

DOI: https://doi.org/10.1016/j.cattod.2018.02.036

IF: 5.3

2018-01-01

Catalysis Today

Abstract:Catalytic steam reforming of long-chain hydrocarbons has drawn great attention for hydrogen production, which can be used for on-board/on-site fuel cell. Novel catalysts of Ni-Ce-Pr solid oxide with high activity and stability for steam reforming of n-dodecane have been developed via a citric-acid-assisted sol-gel method. High hydrogen production with the rate of 5917.1 umol/min under 600 °C at a water-to-carbon ratio of 2 has been achieved.
Reaction Pathway for Coke-Free Methane Steam Reforming on a Ni/CeO2 Catalyst: Active Sites and the Role of Metal-Support Interactions

Agustín Salcedo,Pablo G Lustemberg,Ning Rui,Robert M Palomino,Zongyuan Liu,Slavomir Nemsak,Sanjaya D Senanayake,José A Rodriguez,M Verónica Ganduglia-Pirovano,Beatriz Irigoyen

DOI: https://doi.org/10.1021/acscatal.1c01604

2021-07-02

Abstract:Methane steam reforming (MSR) plays a key role in the production of syngas and hydrogen from natural gas. The increasing interest in the use of hydrogen for fuel cell applications demands development of catalysts with high activity at reduced operating temperatures. Ni-based catalysts are promising systems because of their high activity and low cost, but coke formation generally poses a severe problem. Studies of ambient-pressure X-ray photoelectron spectroscopy (AP-XPS) indicate that CH4/H2O gas mixtures react with Ni/CeO2(111) surfaces to form OH, CH x , and CH x O at 300 K. All of these species are easy to form and desorb at temperatures below 700 K when the rate of the MSR process is accelerated. Density functional theory (DFT) modeling of the reaction over ceria-supported small Ni nanoparticles predicts relatively low activation barriers between 0.3 and 0.7 eV for complete dehydrogenation of methane to carbon and the barrierless activation of water at interfacial Ni sites. Hydroxyls resulting from water activation allow for CO formation via a COH intermediate with a barrier of about 0.9 eV, which is much lower than that through a pathway involving lattice oxygen from ceria. Neither methane nor water activation is a rate-determining step, and the OH-assisted CO formation through the COH intermediate constitutes a low-barrier pathway that prevents carbon accumulation. The interactions between Ni and the ceria support and the low metal loading are crucial for the reaction to proceed in a coke-free and efficient way. These results pave the way for further advances in the design of stable and highly active Ni-based catalysts for hydrogen production.
Lamellar cross-linking Ni/CeO 2 as an efficient and durable catalyst for dry reforming of methane

Huanhuan Xia,Chengxiong Dang,Dan Zhou,Weiquan Cai

DOI: https://doi.org/10.1016/j.cej.2024.151365

IF: 15.1

2024-04-21

Chemical Engineering Journal

Abstract:Dry reforming of methane provides a prospective process for converting greenhouse gases into syngas but suffers from the coking and sintering of catalyst at high operating temperatures. Here we report a lamellar cross-linking Ni/CeO 2 catalyst that shows durable performance with 73 % CO 2 and 60 % CH 4 conversions for DRM at 700 °C in a continuous operation of 50 h. The sintering of Ni particles is inhibited due to the confined migration and aggregation of Ni nanoparticles provided by the lamellar CeO 2 nanosheets. Meanwhile, the presence of these CeO 2 nanosheets facilitates the release of lattice oxygen and the formation of oxygen vacancies, thereby generating more reactive oxygen species, as revealed by the characterization of Raman, XPS, H 2 -TPR and O 2 -TPD. The catalyst characterization using TGA and N 2 -TP indicates that the reactive oxygen species can realize the in-situ gasification of carbon deposition, thus achieving a balance between the rate of coke formation and carbon gasification. Due to the dynamic balance of carbon deposits, no further accumulation of carbon deposition is observed during the DRM test from 10 h to 50 h.

engineering, chemical, environmental
Identifying the roles of Ce3+−OH and Ce−H in the reverse water-gas shift reaction over highly active Ni-doped CeO2 catalyst

Haidong Shen,Yujuan Dong,Shaowei Yang,Yuan He,Qimeng Wang,Yueling Cao,Wenbin Wang,Tianshuai Wang,Qiuyu Zhang,Hepeng Zhang

DOI: https://doi.org/10.1007/s12274-022-4207-8

IF: 9.9

2022-04-18

Nano Research

Abstract:Nickel-CeO2-based materials are commonly used for the thermal catalytic hydrogenation of CO2. However, high Ni loadings and low CO selectivity restrict their use in the reverse water-gas shift (RWGS) reaction. Herein, we demonstrate a highly active, robust, and low-Ni-doped (1.1 wt.%) CeO2 catalyst (1.0−Ni−CeO2). The Ni-based-mass-specific CO formation rate reaches up to 1,542 mmol·gNi−1·h−1 with 100% CO selectivity at 300 °C for 100 h, among the best values reported in the literature. Density functional theory (DFT) and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) results reveal that the enhanced catalytic activity is attributed to the abundant Ce−H species, while the high selectivity results from low CO affinity. More importantly, a new reaction mechanism is proposed, which involves the reduction of bicarbonate to generate formate intermediate and CO by the H− released from Ce−H species. The new findings in this work will benefit the design of economic, efficient, and robust catalysts for low-temperature RWGS reactions.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology

Modulating oxidation state of Ni/CeO 2 catalyst for steam methane reforming: a theoretical prediction with experimental verification

Modulating Oxidation State of Ni/CeO2 Catalyst for Steam Methane Reforming: a Theoretical Prediction with Experimental Verification

CO and Methane Oxidation Over CeXZr1-XO2 Mixed Oxide Supported PdO Catalysts

Methanol steam reforming over Ni-CeO2 model and powder catalysts: Pathways to high stability and selectivity for H2/CO2 production

Oxygen Vacancy Induced Strong Metal-Support Interactions on Ni/Ce0.8Zr0.2O2 Nanorod Catalysts for Promoting Steam Reforming of Toluene: Experimental and Computational Studies.

Dynamics of the Cu/CeO2 Catalyst during Methanol Steam Reforming

Rational design of nickel-based catalyst coupling with combined methane reforming to steadily produce syngas

Ni/CeO2 Catalyst Prepared via Microimpinging Stream Reactor with High Catalytic Performance for CO2 Dry Reforming Methane

Ni/Ce0.9Eu0.1O1.95 with enhanced coke resistance for dry reforming of methane

Effect of Ceria Amount on Promoting Ni-Co/SBA-15 Catalyst for n-Dodecane Steam Reforming

Enhanced activity and stability of Ce-doped PrCrO3-supported nickel catalyst for dry reforming of methane

CO2 Reforming of CH4 over Rare Earth Elements Functionalized Mesoporous Ni–Ln (ln = Ce, La, Sm, Pr)–Al–O Composite Oxides

Bimetallic NiFe Nanoparticles Supported on CeO2 as Catalysts for Methane Steam Reforming

Preparing a Zr-Doped CeO 2 Nanorod to Improve the Catalytic Performance of the Ni-Based Catalyst for Dry Reforming of Methane by Enhancing Oxygen Supply

Enhancement of hollow Ni/CeO2-Co3O4 for CO2 methanation: From CO2 adsorption and activation by synergistic effects

Fabrication of CeZrO2 on Ni/SiO2 and Promoted Catalysis for Methane Autothermal Reforming in a Fluidized Bed Reactor

Unraveling the effects of Ce/Zr molar ratio in mesoporous CexZr1−xO2 on the performance of dry reforming of methane over the supported Ni catalysts

n-Dodecane steam reforming catalyzed by Ni-Ce-Pr catalysts. Part 1: Catalyst preparation and Pr doping

Reaction Pathway for Coke-Free Methane Steam Reforming on a Ni/CeO2 Catalyst: Active Sites and the Role of Metal-Support Interactions

Lamellar cross-linking Ni/CeO 2 as an efficient and durable catalyst for dry reforming of methane

Identifying the roles of Ce3+−OH and Ce−H in the reverse water-gas shift reaction over highly active Ni-doped CeO2 catalyst