Abstract:Numerous attempts have been made to develop ion-exchange membranes with low resistance for various applications such as electrodialysig and fuel cells. In this study, the strategies of immersion precipitation and dry-casting were combined, to control the membrane porosity with the purpose of improving the physical and electrochemical properties of ion-exchange membranes. The porosity was tuned using the time of membrane exposure to an elevated temperature environment. In addition to controlling the porosity to balance the membrane electrical resistance with the diffusion caused by the concentration gradient, it was experimentally shown that the porosity can influence the IEC and water uptake of the membrane and, thus, further affect the resistance. Furthermore, the surface hydrophilicity was characterized by water contact angle measurements; the results revealed that the porous membranes were more hydrophilic than the dense membranes. As demonstrated by experimental data for desalination by electrodialysis, it was found that a membrane dried at 60 degrees C for 1 h had the highest desalination efficiency. This is mainly because porous membranes facilitate the transport of ions. Compared to membranes with higher porosity, the membrane prepared with a 1-h aging time had more steric hindrance, which can decrease the diffusion of ions, so that a superior desalination efficiency can be obtained. To further investigate the impact of the density of -SO32- functional groups on the electrodialysis process, membranes with various weight ratios of poly(ether sulfone) (PES) to sulfonated poly(ether sulfone) (SPES) were prepared. With increasing content of SPES, the physical and electrochemical properties of the newly developed porous membranes were changed. A membrane with higher density of functional groups was found to have a higher desalination efficiency, because of the electrostatic effect of the membrane. These results were consistent with the current efficiency. Under optimal membrane preparation conditions, the obtained membrane had a high IEC (1.75 mmol/g) and water uptake (168%). The desalination efficiency reached 95%, and the current efficiency reached 100%. It was concluded that the performance of a porous membrane with controllable porosity can enhance the electrodialysis (ED) process with respect to energy efficiency and desalination efficiency. New methods of fabricating membranes with pores such as immersion precipitation and dry-casting are thought to be potential routes to decreasing the electrical resistance.

Asymmetric porous cordierite ceramic membranes prepared by phase inversion tape casting and their desalination performance

Asymmetric porous cordierite hollow fiber membrane for microfiltration

Hydrophobic porous alumina hollow fiber for water desalination via membrane distillation process

Asymmetric alumina-based ultrathin composite ceramic membranes with interfacial modification of black talc nanosheets

Compact SiOC Ceramic Composite Nanofiltration Membranes by Slow Dip Coating for Water Purification

Preparation and Properties of Asymmetric Porous Aluminium-Oxide Ceramic Hollow Fibre Membranes

Combing Three-Dimensional Water Channels and Ultra-Thin Skin Layer Enable High Flux and Stability of Loose Polyimide/sio2 Nanofiltration Membranes at Low Operating Pressure Via One Step In-Situ Modification

Preparation and Characterization of PVDF/nonwoven Fabric Flat-Sheet Composite Membranes for Desalination Through Direct Contact Membrane Distillation

A novel strategy to enhance the desalination stability of FAS (fluoroalkylsilane)-modified ceramic membranes via constructing a porous SiO2@PDMS (polydimethylsiloxane) protective layer on their top

Hydrophobic silica sand ceramic hollow fiber membrane for desalination via direct contact membrane distillation

In Situ-Grown Al2O3 Nanoflowers and Hydrophobic Modification Enable Superhydrophobic SiC Ceramic Membranes for Membrane Distillation

Porous Silicate Cement Membranes Generated by the Novel Method Combining Freeze Casting and Heat-Dry Curing

Co-pressing and co-sintering preparation of cost-effective and high-performance asymmetric ceramic membrane for oily wastewater treatment

Eco-Friendly Superhydrophobic Modification of Low-Cost Multi-Layer Composite Mullite Base Tubular Ceramic Membrane for Water Desalination

Novel Fabrication Processing of Porous Al2O3/CaAl12O19 Membrane by Combining Emulsion, Cement Curing and Tape-Casting Methods

Nanoarchitectonics of High‐Performance Bis(triethoxysilyl)methane (BTESM) Hybrid‐Silica Membrane for Pervaporative Desalination Applications

A Co-Casting Route Enables the Formation of Skinless, Hydrophobic Poly (vinylidene Fluoride) Membranes for DCMD

Robust super-hydrophobic inorganic nanoparticles modified layered structure Si2N2O membrane for membrane distillation

Cation-Exchange Membranes with Controlled Porosity in Electrodialysis Application

Fabrication of a Charged PDA/PEI/Al2O3 Composite Nanofiltration Membrane for Desalination at High Temperatures

Superhydrophobic β-Sialon-mullite ceramic membranes with high performance in water treatment