Abstract:The injection strategy is commonly manipulated to control the stratification level to simultaneously achieve a low pollutant emission and a high efficiency in internal combustion engines. This paper reports on a joint experimental and numerical study of the emission characteristics and engine performance in a heavy-duty directinjection compression ignition (DICI) engine operating in the HCCI and PPC regimes, with a primary reference fuel made up of iso-octane (81% by volume) and n-heptane (19%) as a model gasoline fuel. The injection timing was varied to achieve different levels of stratification of the charge in the cylinder while the intake air temperature was adjusted accordingly to keep the same combustion phasing at 3 degrees crank angle (CA) after top dead centre (ATDC). The main results of the present study are: (1) In gasoline DICI engines, the fuel is injected into the cylinder at an earlier SOI. The combustion process can be divided into different regimes, HCCI, PPC, and transition from HCCI to PPC, depending on SOI. Two distinctive classes of in-cylinder combustion temperature distributions could be found from the simulation results for the studied engine: one was for the SOI range from -100 to -48 degrees CA ATDC, which was the HCCI regime and/ or the transition from HCCI to PPC regime, where the mean effective in-cylinder temperature was lower than 1700 K. The second class was for the SOI range from -44 to -20 degrees CA ATDC, where the combustion temperature was higher than 1850 K. This corresponded to the PPC regime. (2) The NOx emission was not only affected by the mean temperature but also the distribution of temperature in the cylinder. (3) The main source of unburned hydrocarbon (UHC) emission in the HCCI and the transition regimes was the fuel trapped in the crevice region where the oxidation process could not function properly. (4) Carbon monoxide (CO) emissions showed a non-monotonic variation with the injection timing, with one peak forming in the bowl region and one forming in the squish region during the transition from HCCI to PPC. The main source of CO emission was in the low temperature and fuel-lean region in the cylinder. (5) In the present engine operation, the pressure rise rate (PRR) in the PPC regime was higher than that in the HCCI regime, which is contrary to most results reported in the literature. This is a combined effect of low equivalence ratio in the piston bowl and in the squish region, and the stratification of the ignition delay time in the mixture. (6) Highest thermodynamic efficiency was achieved in the PPC regime with SOI from -44 to -31 degrees CA ATDC. In the transition from HCCI to PPC regime, the thermodynamic efficiency reached its lowest due to the poor combustion efficiency.

Effect of piston bowl geometry and compression ratio on in-cylinder combustion and engine performance in a gasoline direct-injection compression ignition engine under different injection conditions

Experimental Investigation of Injection Strategies on Low Temperature Combustion Fuelled with Gasoline in A Compression Ignition Engine

Emission Characteristics and Engine Performance of Gasoline DICI Engine in the Transition from HCCI to PPC

Experimental Study on the Influence of Low-Temperature Combustion (LTC) Mode and Fuel Properties on Cyclic Variations in a Compression-Ignition Engine

An Experiment Study of Homogeneous Charge Compression Ignition Combustion and Emission in A Gasoline Engine

Effect of piston bowl geometry and spray angle on engine performance and emissions in HCCI engine using multi‐stage injection strategy

Investigation on Combining Partially Premixed Compression Ignition and Diffusion Combustion for Gasoline Compression Ignition—Part 2: Compression Ratio and Piston Bowl Geometry Effects

Effects of the Intake Pressure on Gasoline Low Temperature Compression Ignition

Influence of Fuel and Operating Conditions on Combustion Characteristics of a Homogeneous Charge Compression Ignition Engine

An Experimental Investigation of the Effects of Fuel Injection Strategy on the Efficiency and Emissions of a Heavy-Duty Engine at High Load with Gasoline Compression Ignition

Experimental Study on the Effect of Pre-Ignition Heat Release on GCI Engine Combustion

Experimental Study on the Effects of Mixture Homogeneity on Stratified-Charge Compression Ignition Combustion

Exploring the Effects of the Key Multi-Injection Parameters on Combustion and Emissions in Intelligent Charge Compression Ignition (ICCI) Mode

Effects of Research Octane Number of Gasoline and Dual Direct Injection Strategies on Combustion and Emission Performance of Intelligent Charge Compression Ignition (ICCI) Mode

Effects of Inlet Pressure and Octane Numbers on Combustion and Emissions of a Homogeneous Charge Compression Ignition (HCCI) Engine

Combustion Characteristics of Gasoline DICI Engine in the Transition from HCCI to PPC: Experiment and Numerical Analysis

Effects of different injection strategies on mixing, combustion and emission behavior of gasoline compression ignition (GCI) engines

Effects of Pilot Injection Strategy on Combustion and Emission Characteristics in Gasoline Compression Ignition

Effects of Intake Conditions and Octane Sensitivity on GCI Combustion at Early Injection Timings

Experimental investigation on the combustion and emissions in a pilot ignited direct injection natural gas engine using HCDI strategy

The Lean-Burn Limit Extending Experiment on Gasoline Engine with Dual Injection Strategy and High Power Ignition System