Abstract:Amid rising demands for fuel efficiency and emissions reduction, enhancing the thermal efficiency of gasoline engines has become imperative, which requires higher efficiency combustion strategies and integrated optimized design to maximize the work output from fuel. In gasoline engine, both increasing the compression ratio and using lean burn mode improve the ratio of useful work output to the energy input effectively, which resulting in higher thermal efficiency. Although there is limited scope for increasing the compression ratio due to the higher sensitivity to knocking, especially under stoichiometric conditions, reduced sensitivity could be got with leaner mixture fill into cylinder, which can further increase the specific heat ratio and thermal efficiency. However, realizing the efficiency benefits of lean burn in gasoline engines necessitates overcoming critical challenges like ensuring robust ignition process and accelerating burning rates to achieve short, stable combustion durations. To overcome these problems, a kind of pre-chamber ignition concept has been developed, which integrate a dedicate injector and spark plug into one assembly on cylinder head. In this paper, the focus is on the development of such a system and the combustion characteristics on gasoline engine with it.Primary experimental data is obtained by an ultra-lean single cylinder research gasoline engine equipped with pre-chamber concept. Key structure parameters such as pre-chamber volumetric fraction and jet hole have been comparatively investigated. Experimental study also be performed on a multi-cylinder engine equipped with the same pre-chamber concept in order to verify the maximum Gross-ITE and BTE simultaneously. Results indicated that optimized pre-chamber structure design could make much contribute to the thermal efficiency under ultra-lean mode with lambda up to 2.1. Under this condition, combustion stability was also significantly improved compared to spark ignition with faster and knock-free combustion process. Due to the lower temperature of ultra-lean combustion, Nitrogen Oxides emissions can be significantly reduced. Furthermore, for a given load, it was shown that maximum GITE of 50% on SCE was measured at 2500rpm-11.5bar IMEP together with the maximum BTE of 46.3% on MCE under the same operating condition.

Optimization of Piston Bowl and Valve System in Compression Ignition Engine Fueled with Gasoline/diesel/polyoxymethylene Dimethyl Ethers for High Efficiency

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

The Lean-Burn Limit Extending Experiment on Gasoline Engine with Dual Injection Strategy and High Power Ignition System

Computational Optimization of the Piston Bowl Geometry for the Different Combustion Regimes of the Dual-Mode Dual-Fuel (DMDF) Concept Through an Improved Genetic Algorithm

Experimental Study of Stratified Lean Burn Characteristics on a Dual Injection Gasoline Engine

Investigations on combustion system optimization of a heavy-duty natural gas engine

An Experimental Investigation of the Effects of Fuel Injection Strategy on the Efficiency and Emissions of a Heavy-Duty Engine at High Load with Gasoline Compression Ignition

Improvement of high load performance in gasoline compression ignition engine with PODE and multiple-injection strategy

Effects of Dual Injection Strategies on Combustion, Heat-Work Conversion Process and Emissions of a Spark Ignition Engine Fuelled with E20 Blends

Towards Low Emissions and High Thermal Efficiency of Gasoline Compression Ignition Engine under High Loads by Modulating the Fuel Reactivity and Injection Strategy

Thermal efficiency improvement of lean burn high compression ratio engine coupled with water direct injection

Optimization on emissions and thermal efficiency of diesel engine under two combustion modes based on the synergy between late intake valve closing and EGR

Combined Effects of Fuel Reactivity and Intake Thermodynamic Conditions on Heat Release and Emissions of Compression Ignition Combustion

Effects of Piston Bowl Geometries On Diesel and Gasoline Dual-Fuel Combustion under Low Load Conditions

Numerical Study On The Approach For Super-High Thermal Efficiency In A Gasoline Homogeneous Charge Compression Ignition Lean-Burn Engine

Multi-point Micro-Flame Ignited Hybrid Lean-Burn Combustion of Gasoline with Direct Injection Dimethyl Ether

Pre-Chamber Combustion System Development for an Ultra-Lean Gasoline Engine

Experimental Study On High-Load Extension Of Gasoline/Pode Dual-Fuel Rcci Operation Using Late Intake Valve Closing

Improving the lean burn performance of a high compression ratio methanol engine by multiple-injection

Applications of Oxyhydrogen, Direct Water Injection, and Early-Intake Valve Closure Technologies on a Petrol Spark Ignition Engine—A Path towards Zero-Emission Hydrogen Internal Combustion Engines

Improvement of combustion and emission by combined combustion of ethanol premix and gasoline direct injection in SI engine