Abstract:Abstract Gasoline compression ignition (GCI) is a promising powertrain solution to simultaneously address the increasingly stringent regulation of oxides of nitrogen (NOx) and a new focus on greenhouse gases. GCI combustion benefits from extended mixing times due to the low reactivity of gasoline, but only when held beneath the threshold of the high temperature combustion regime. The geometric compression ratio (GCR) of an engine is often chosen to balance the desire for low NOx emissions while maintaining high efficiency. This work explores the relationship between GCR, variable valve actuation (VVA) and emissions when using GCI combustion strategies. The test article was a Cummins ISX15 heavy-duty diesel engine with an unmodified production air and fuel system. The test fuel was an ethanol-free gasoline with a market-representative research octane number (RON) of 91.4–93.2. In the experimental investigation at 1375 rpm/10 bar BMEP, three engine GCRs were studied, including 15.7, 17.3, and 18.9. Across the three GCRs, GCI exhibited a two-stage combustion process enabled through a split injection strategy. When keeping both NOx and CA50 constant, varying GCR from 15.7 to 18.9 showed only a moderate impact on engine brake thermal efficiency (BTE), while its influence on smoke was pronounced. At a lower GCR, a larger fraction of fuel could be introduced during the first injection event due to lower charge reactivity, thereby promoting partially-premixed combustion and reducing smoke. Although increasing GCR increased gross indicated thermal efficiency (ITEg), it was also found to cause higher energy losses in friction and pumping. In contrast, GCI performance showed stronger sensitivity towards EGR rate variation, suggesting that air-handling system development is critical for enabling efficient and clean low NOx GCI combustion. To better utilize gasoline’s lower reactivity, an analysis-led variable valve actuation investigation was performed at 15.7 GCR and 1375 rpm/10 bar BMEP. The analysis was focused on using an early intake valve closing (EIVC) approach by carrying out closed-cycle, 3-D CFD combustion simulations coupled with 1-D engine cycle analysis. EIVC was shown to be an effective means to lengthen ignition delay and promote partially-premixed combustion by lowering the engine effective compression ratio (ECR). By combining EIVC with a tailored fuel injection strategy and properly developed thermal boundary conditions, simulation predicted a 2.3% improvement in ISFC and 47% soot reduction over the baseline IVC case while keeping NOx below the baseline level.

The Effect of Control Strategies on the Gasoline Compression Ignition (GCI) Engine: Injection Strategy, Exhaust Residual Gas Strategy, Biodiesel Addition Strategy, and Oxygen Content Strategy

Gasoline Compression Ignition (GCI) Combustion in a Light-Duty Engine Using Double Injection Strategy

Effects of different injection strategies on mixing, combustion and emission behavior of gasoline compression ignition (GCI) engines

Effects of injection strategies coupled with gasoline-hydrogenated catalytic biodiesel blends on combustion and emission characteristics in GCI engine under low loads

Experimental Study the Effect of Injection Strategies on Combustion and Emission Characteristics in Gasoline Compression Ignition Engines Using Gasoline/hydrogenated Catalytic Biodiesel Blends

Numerical Investigation of the Effect of Injection Timing on the In-Cylinder Activity of a Gasoline Direct Injection Engine

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

Study on the Influence Mechanism of Mixture Stratification on GCI Combustion and the Compound Injection Strategy under High Load Operation

Impact of Geometric Compression Ratio and Variable Valve Actuation on Gasoline Compression Ignition in a Heavy-Duty Diesel Engine

Experimental Study on Combustion and Emission Characteristics of Gasoline Compression Ignition Engines under Cooperative Control of Operating Parameters

Gasoline Compression Ignition Operation on a Multi-Cylinder Heavy Duty Diesel Engine

A Methodology for Regulating Fuel Stratification and Improving Fuel Economy of GCI Mode Via Double Main-Injection Strategy

An Investigation on Gasoline Compression Ignition (GCI) Combustion in a Heavy-Duty Diesel Engine Using Gasoline/hydrogenated Catalytic Biodiesel Blends

Towards Low Emissions and High Thermal Efficiency of Gasoline Compression Ignition Engine under High Loads by Modulating the Fuel Reactivity and Injection Strategy

An Experimental Investigation of the Effects of Fuel Injection Strategy on the Efficiency and Emissions of a Heavy-Duty Engine at High Load with Gasoline Compression Ignition

Pilot injection strategy management of gasoline compression ignition (GCI) combustion in a multi-cylinder diesel engine

Investigation of Injection Parameters Coupled with Fuel Reactivity on Combustion and Emissions in Dual Direct-Injection GCI Engine

Co-optimization of Operating Parameters, Fuel Composition, and Piston Bowl Geometry of Gasoline Compression Ignition (GCI) Engine at High Loads

Effects of Ozone Addition and Octane Sensitivity on Combustion Characteristics of Gasoline Compression Ignition Engines

Experimental Investigation on Knocking Combustion Characteristics of Gasoline Compression Ignition Engine

Optimizing Gasoline Compression Ignition Engine Performance and Emissions: Combined Effects of Exhaust Gas Recirculation and Fuel Octane Number