Abstract:The simultaneous application of new low-NOx emissions standards and greenhouse gas (GHG) rules has placed great pressure on the commercial vehicle industry and has driven demand for innovative solutions. One potential solution, gasoline compression ignition (GCI), utilizes gasoline’s lower reactivity to promote partially premixed combustion and extract efficiency while reducing the PM-NOx trade-off curve. Gasoline’s volatility allows for the use of higher levels of exhaust gas recirculation (EGR), a key enabler of GCI combustion. In order to deliver higher levels of EGR while maintaining sufficient boost pressure, a tailored and efficient air-handling system is critical. This work presents the analysis-led development of a low-NOx GCI air-handling system including both turbocharger matching and EGR configuration for a prototype heavy-duty GCI engine based on a model year 2013 Cummins ISX diesel engine using low octane gasoline (RON80). In the analysis-driven development process, a 1D engine system-level analysis was closely coupled with closed-cycle 3D CFD GCI combustion development. Three different boost systems were investigated using a validated 1D engine model: 1) the production turbocharger; 2) an off-the-shelf single-stage waste-gate turbocharger; 3) a prototype single-stage variable geometry turbocharger. For each boost system, three EGR configurations were evaluated: 1) a high-pressure EGR route; 2) a low-pressure EGR route; 3) a dual-loop EGR route. The air-handling system performance was first investigated over five steady-state engine operating conditions extracted from the ramped modal cycle supplemental emissions test. Then, through cosimulation using a Simulink-based engine controls model, the best performing candidates under transient operation through the Heavy-Duty Federal Test Procedure certification cycle were identified. The production turbocharger, designed for 4–6 g/kWh engine-out NOx, suffered from low combined turbocharger efficiency under the low-NOx GCI thermal boundary conditions. The prototype 1-Stage variable geometry turbocharger, when used with a high-pressure EGR configuration, demonstrated higher combined efficiencies, while the waste-gate turbocharger showed the best results when used with a dual-loop EGR system. All low-pressure only EGR configurations were found to incur additional pumping penalties due to the need for a back pressure valve to drive sufficient EGR levels. In the transient test cycle analysis, the single-stage high-pressure EGR system was capable of delivering the target boost and EGR, while the off-the-shelf waste-gate turbocharger, with its higher mass inertia, showed slower turbine response and a resulting lag in boost response. Unsurprisingly, the dual-loop EGR system also suffered from delays in EGR delivery during engine acceleration. In summary, the prototype single-stage variable geometry turbocharger with a high-pressure EGR system produced the best performance over both the steady-state and transient engine cycles and was identified as the best candidate for the prototype low-NOx heavy-duty GCI engine.

Gasoline Compression Ignition (GCI) Combustion in a Light-Duty Engine Using Double Injection Strategy

Experimental Investigation of a Heavy-Duty CI Engine Retrofitted to Natural Gas SI Operation

Gasoline Compression Ignition Operation on a Multi-Cylinder Heavy Duty Diesel Engine

Impact of Geometric Compression Ratio and Variable Valve Actuation on Gasoline Compression Ignition in a Heavy-Duty Diesel Engine

High-efficiency Combustion of Gasoline Compression Ignition (GCI) Mode with Medium-Pressure Injection of Low-Octane Gasoline under Wide Engine Load Conditions

Effects of injection strategies coupled with gasoline-hydrogenated catalytic biodiesel blends on combustion and emission characteristics in GCI engine under low loads

The Effect of Control Strategies on the Gasoline Compression Ignition (GCI) Engine: Injection Strategy, Exhaust Residual Gas Strategy, Biodiesel Addition Strategy, and Oxygen Content Strategy

Towards Low Emissions and High Thermal Efficiency of Gasoline Compression Ignition Engine under High Loads by Modulating the Fuel Reactivity and Injection Strategy

Pilot injection strategy management of gasoline compression ignition (GCI) combustion in a multi-cylinder diesel engine

Effects of different injection strategies on mixing, combustion and emission behavior of gasoline compression ignition (GCI) engines

A Methodology for Regulating Fuel Stratification and Improving Fuel Economy of GCI Mode Via Double Main-Injection Strategy

An Investigation on Gasoline Compression Ignition (GCI) Combustion in a Heavy-Duty Diesel Engine Using Gasoline/hydrogenated Catalytic Biodiesel Blends

Experimental Study the Effect of Injection Strategies on Combustion and Emission Characteristics in Gasoline Compression Ignition Engines Using Gasoline/hydrogenated Catalytic Biodiesel Blends

Numerical Investigation of the Effect of Injection Timing on the In-Cylinder Activity of a Gasoline Direct Injection Engine

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

An Experimental and Computational Investigation of Tailor-Developed Combustion and Air-Handling System Concepts in a Heavy-Duty Gasoline Compression Ignition Engine

Achieving High Efficient Gasoline Compression Ignition (GCI) Combustion Through the Cooperative-Control of Fuel Octane Number and Air Intake Conditions

Tailored Air-Handling System Development for Gasoline Compression Ignition in a Heavy-Duty Diesel Engine

Experimental Study on Combustion and Emission Characteristics of Gasoline Compression Ignition Engines under Cooperative Control of Operating Parameters

Optimizing Gasoline Compression Ignition Engine Performance and Emissions: Combined Effects of Exhaust Gas Recirculation and Fuel Octane Number

Development of a Gasoline Direct Injection Compression Ignition (GDCI) Engine