Abstract:The injection strategy is commonly manipulated to control the stratification level to simultaneously achieve a low pollutant emission and a high efficiency in internal combustion engines. This paper reports on a joint experimental and numerical study of the emission characteristics and engine performance in a heavy-duty directinjection compression ignition (DICI) engine operating in the HCCI and PPC regimes, with a primary reference fuel made up of iso-octane (81% by volume) and n-heptane (19%) as a model gasoline fuel. The injection timing was varied to achieve different levels of stratification of the charge in the cylinder while the intake air temperature was adjusted accordingly to keep the same combustion phasing at 3 degrees crank angle (CA) after top dead centre (ATDC). The main results of the present study are: (1) In gasoline DICI engines, the fuel is injected into the cylinder at an earlier SOI. The combustion process can be divided into different regimes, HCCI, PPC, and transition from HCCI to PPC, depending on SOI. Two distinctive classes of in-cylinder combustion temperature distributions could be found from the simulation results for the studied engine: one was for the SOI range from -100 to -48 degrees CA ATDC, which was the HCCI regime and/ or the transition from HCCI to PPC regime, where the mean effective in-cylinder temperature was lower than 1700 K. The second class was for the SOI range from -44 to -20 degrees CA ATDC, where the combustion temperature was higher than 1850 K. This corresponded to the PPC regime. (2) The NOx emission was not only affected by the mean temperature but also the distribution of temperature in the cylinder. (3) The main source of unburned hydrocarbon (UHC) emission in the HCCI and the transition regimes was the fuel trapped in the crevice region where the oxidation process could not function properly. (4) Carbon monoxide (CO) emissions showed a non-monotonic variation with the injection timing, with one peak forming in the bowl region and one forming in the squish region during the transition from HCCI to PPC. The main source of CO emission was in the low temperature and fuel-lean region in the cylinder. (5) In the present engine operation, the pressure rise rate (PRR) in the PPC regime was higher than that in the HCCI regime, which is contrary to most results reported in the literature. This is a combined effect of low equivalence ratio in the piston bowl and in the squish region, and the stratification of the ignition delay time in the mixture. (6) Highest thermodynamic efficiency was achieved in the PPC regime with SOI from -44 to -31 degrees CA ATDC. In the transition from HCCI to PPC regime, the thermodynamic efficiency reached its lowest due to the poor combustion efficiency.

Effect Of Injection Timing On Gasoline Homogeneous Charge Compression Ignition Particulate Emissions

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

Numerical Investigation of the Effect of Injection Timing on the In-Cylinder Activity of a Gasoline Direct Injection Engine

Influence of Inlet Air Temperature on Gasoline HCCI Particulate Emissions

Effect of Injection Parameters on PCCI Combustion and Emissions in a Diesel Engine

Effects of Multi-Injection Mode on Diesel Homogeneous Charge Compression Ignition Combustion

Effect and optimization of injection timing on the combustion and particle emission of a gasoline engine

Particulate Emission and Combustion Characteristics of a Direct-Injection Natural Gas Engine under Various Injection and Ignition Timings

Effect of injection timing on PM emissions from DMCC engine

Experimental Study on the Particulate Matter Emission Characteristics for A Direct-Injection Gasoline Engine

Effects of engine load, inlet air temperature, valve overlap and EGR on diesel HCCI engine

Combustion Characteristics and Particulate Emission in A Natural-Gas Direct-Injection Engine: Effects of the Injection Timing and the Spark Timing

Investigation of the Effects of Split-Injection on Particle Emissions from a Dieseline CI Engine

Particulate Size Distribution from Diesel–Dimethyl Ether Dual Fuel Premixed Compression Ignition Combustion Engine

Impact of Fuel and Injection System on Particle Emissions from A Gdi Engine

Emission Characteristics and Engine Performance of Gasoline DICI Engine in the Transition from HCCI to PPC

Effect of piston bowl geometry and compression ratio on in-cylinder combustion and engine performance in a gasoline direct-injection compression ignition engine under different injection conditions

Effects of multiple injection strategies on gaseous emissions and particle size distribution in a two-stroke compression-ignition engine operating with the gasoline partially premixed combustion concept

Analysis of the Particulate Emissions and Combustion Performance of A Direct Injection Spark Ignition Engine Using Hydrogen and Gasoline Mixtures

Effect of Direct In-Cylinder CO2 Injection on HCCI Combustion and Emission Characteristics

Effect of Injection Strategy on Emission Characteristics of Compression Ignition Engine Fueled with Blended Fuel