Abstract:As we know, 3DPC is printed layer by layer compared with mold-casting conventional concrete. Pore structure and layer-to-layer interface are two main aspects of the internal structure for 3DPC, which decide 3DPC's mechanical performance. The layer-to-layer interface caused by printing is specific to 3DPC. The emphasis of this study lies in the layer-to-layer interfaces of 3DPC. The first aim of this study is to quantify the characteristics of the layer-to-layer interface and therefore characterize different aspects of the interfaces. The second aim of this study is to explore how the internal structure of printed concrete influences the mechanical performance of 3DPC. This research set out to design a series of experimental comparisons between 3DPC and casted concrete with the same compositions. Mechanical tests, i.e., compressive stress, ultrasonic Pulse Velocity test, flexural tension, and tension splitting, as well as the Ultrasonic Pulse Velocity test, were performed to check the mechanical performance of 3DPC. Contrary to what has often been expected, the mechanical test results showed the printed concrete has a quality not worse than casted concrete with the same recipe. Meanwhile, the X-ray computed tomography (X-CT) is used to characterize the internal structure, pore shapes, and interfaces of 3DPC. First, the investigation revealed that the lower total porosity and fewer big voids could be the fundamental causes meaning 3DPC has a better mechanical performance than casted concrete. Second, the statistics based on aspect ratio show that the distribution curves follow similar trends, regardless of the printed or casted concrete. Third, this study quantified the depth of the different interfaces for 3DPC. The results suggest that the porosity in an interface varies in a range. The author's pioneer work has contributed to our present understanding of the interfaces of 3DPC.

Impact of groove-and-tongue parameters on the bonding behavior between 3d-printed UHP-SHCC and cast normal concrete

Investigation of the Internal Structure of Hardened 3D-Printed Concrete by X-CT Scanning and Its Influence on the Mechanical Performance.

Interfacial bonding performance of 3D-printed Ultra-High Performance Strain-Hardening Cementitious Composites (UHP-SHCC) and cast normal concrete

Bond shear performances and constitutive model of interfaces between vertical and horizontal filaments of 3D printed concrete

Bonding performance of 3D printing concrete with self-locking interfaces exposed to compression–shear and compression–splitting stresses

3D-printed concrete permanent formwork: effect of postcast concrete proportion on interface bonding

Bonding Performance Between Ultra High Toughness Cementitious Composites and Existing Concrete

Interfacial bonding properties of 3D printed permanent formwork with the post-casted concrete

Experimental Study on Direct Shear Performance of Concrete-Concrete Interface of Prefabricated Structure Sleeve Grouting Connection

Interfacial Properties of Three-Dimensional-Printed Permanent Formwork with Cast-in-Place Concrete

Mechanical and macrostructural properties of 3D printed concrete dosed with steel fibers under different loading direction

Tensile performance of 3D-printed Strain-Hardening Cementitious Composites (SHCC) considering material parameters, nozzle size and printing pattern

Effects of 3D-printing on the tensile splitting strength of concrete structures

Research on the Bonding Performance of UHPC–NC Interfaces With Different Sizes of Grooves

EXPERIMENTAL STUDY ON BOND-SLIP BETWEEN ULTRA HIGH TOUGHNESS CEMENTITIOUS COMPOSITES AND STEEL BAR

Strength and Proportioning Design of 3D Printed Concrete (3DPC) Based on Aggregate Gradation Optimization

Experimental Study on Bond Behavior Between CFRP and Concrete with Longitudinal Grooves

Experimental and numerical study on the flexural behavior of 3D-printed composite beams with U-shaped ECC formwork

Flexural performance of nature-inspired 3D-printed strain-hardening cementitious composites (3DP-SHCC) with Bouligand structures

Experimental study and numerical analysis of the interfacial bonding performance of T‐shaped concrete‐filled steel tubes

Bond Performance Between BFRP Bars and 3D Printed Concrete