Abstract:Miniaturization of gas chromatography (GC) instrumentation is of interest because it addresses current and future issues relating to compactness, portability and field application. While incremental advancements continue to be reported in GC with columns fabricated in microchips (referred to in this paper as "microchip columns"), the current performance is far from acceptable. This lower performance compared to conventional GC is due to factors such as pooling of the stationary phase in corners of non-cylindrical channels, adsorption of sensitive compounds on incompletely deactivated surfaces, shorter column lengths and less than optimum interfacing to injector and detector. In this work, a GC system utilizing microchip columns was developed that solves the latter challenge, i.e., microchip interfacing to injector and detector. A microchip compression clamp was constructed to heat the microchip (i.e., primary heater), and seal the injector and detector fused silica interface tubing to the inlet and outlet ports of the microchip channels with minimum extra-column dead volume. This clamp allowed occasional operation up to 375°C and routine operation up to 300°C. The compression clamp was constructed of a low expansion alloy, Kovar™, to minimize leaking due to thermal expansion mismatch at the interface during repeated thermal cycling, and it was tested over several months for more than one hundred injections without forming leaks. A 5.9m long microcolumn with rectangular cross section of 158μm×80μm, which approximately matches a 100μm i.d. cylindrical fused silica column, was fabricated in a silicon wafer using deep reactive ion etching (DRIE) and high temperature fusion bonding; finally, the channel was coated statically with a 1% vinyl, 5% phenyl, 94% methylpolysiloxane stationary phase. High temperature separations of C10-C40 n-alkanes and a commercial diesel sample were demonstrated using the system under both temperature programmed GC (TPGC) and thermal gradient GC (TGGC) conditions. TGGC analysis of a complex essential oil sample was also demonstrated. Addition of a secondary heater and polyimide insulation proved to be helpful in achieving the desired elution temperature without having to raise the primary heater temperature above 300°C for high boiling point compounds.

Microchip Gas Chromatography Column Using Magnetic Beads Coated with Polydimethylsiloxane and Metal Organic Frameworks

A microchip gas chromatography column assembly with a 3D metal printing micro column oven and a flexible stainless-steel column

A Micro Gas Chromatography with Separation Capability Enhanced by Polydimethylsiloxane Stationary Phase Functionalized by Carbon Nanotubes and Graphene.

Microfluidic integration of μPID on μcolumn for ultracompact micro-gas chromatography

A Portable Micro-Gas Chromatography with Integrated Photonic Crystal Slab Sensors on Chip

High-performance MEMS-based gas chromatography column with integrated micro heater

Design, Fabrication, and Evaluation of Microfabricated Columns for Gas Chromatography

Preparation and Application of Chiral Monolithic Column for Capillary Liquid Chromatography

An all-glass based micro gas chromatographic column for light hydrocarbon separation with HKUST-1 as stationary phase

Microfluidic Flow-through SPME Chip for Online Separation and MS Detection of Multiple Analyses in Complex Matrix

Extending the upper temperature range of gas chromatography with all-silicon microchip columns using a heater/clamp assembly

Fabrication of micro-gas chromatograph columns for fast chromatography

Strategies Towards Submicron Size and High-Performance Magnetic PGMA@Fe 3 O 4 @sio 2 –COOH Microspheres with Biological Application

Metal organic framework-organic polymer monolith stationary phases for capillary electrochromatography and nano-liquid chromatography

A Graphitized-Carbon Monolithic Column

Microfabricated planar glass gas chromatography with photoionization detection

Preparation and Characteristics of New Coating for Solid-Phase Microextraction.

Micro gas chromatography column using ionic liquid modified metal-organic framework as stationary phase for rapid breath analysis of gastric cancer

In-situ solvothermal growth of MOF nanocrystals on the fused silica capillary aiming to prepare new gas chromatography column

On-chip Fabry–Pérot interferometric sensors for micro-gas chromatography detection

A magnetic solid phase extraction microfluidic chip coupled with gas chromatography-mass spectrometry for the determination of polycyclic aromatic hydrocarbons in aqueous samples