Abstract:Cylindrical shells have large industrial applications ranging from pressure vessels, engine cylinders and hydraulic chambers to chemical and power plants and they are typically subjected to severe mechanical or thermo-mechanical environmental conditions. The fatigue life, pressure and thermal load bearing capacities of thick-walled cylinders can be considerably improved by inducing near the bore compressive residual hoop stresses. Shrink-fit and autofrettage processes have been effectively applied to generate favorable compressive residual stresses. The main goal of this research study is to fundamentally investigate the compound cylinders subjected to autofrettage and shrink-fit processes and develop new design processing technique and practical design optimization strategies to enhance their fatigue life under cyclic thermo-mechanical loads. First, the residual stresses of compound cylinders subjected to different combinations of shrink-fit and autofrettage processes have been evaluated using the developed finite element model in the ANSYS environment. The stresses due to different cyclic thermo-mechanical loads have also been calculated for the different combinations of compound cylinders considering the fully coupled thermo-elastic finite element model. To validate the finite element model, an experimental setup has been designed to measure the temperature history at three different locations through the wall thickness and also hoop strain at the outer surface of a two-layer compound cylinder under internal quasi-static and cyclic thermal loads. The experimental results have then been compared with those obtained from the finite element model. Moreover, to compare the performance of compound cylinders under different thermo-mechanical loads, the fatigue life due to cyclic pressure, cyclic thermal pulses and cyclic combined thermo-mechanical pulses has been calculated using ASME code for high pressure vessel. Next, to enhance the residual stress distribution along the wall thickness of the cylinder, a new double autofrettage process has been introduced. In the proposed double autofrettage process, an outer autofrettage cycle is performed prior to a standard inner autofrettage cycle. This can provide an increase in the beneficial compressive residual stresses at the near bore area of the cylinder while decreasing the detrimental tensile residual stress at the outer part of the cylinder. The proposed process has then been utilized to construct new combinations of autofrettage, shrink-fit and double autofrettage processes. The residual stress distribution through the thickness and fatigue life of these new combinations have been evaluated and compared with those based on conventional combinations of shrink-fit and autofrettage processes. Finally, a practical design optimization methodology has been developed to identify the optimal configuration of autofrettaged and shrink-fitted cylinders. Optimization problems based on the high-fidelity finite element model is computationally very expensive and may not render accurate optimum results. Considering this in the presented research, design of experiment (DOE) and response surface method (RSM) have been used in combination with the finite element model to create smooth response surface functions which can accurately describe the behavior of the residual hoop stresses with respect to the change of design variables. The developed response surface functions have been effectively utilized in the design optimization problems to simultaneously maximize the residual compressive hoop stress and minimize the residual tensile hoop stress through the thickness of the compound cylinder. Nonlinear mathematical programming technique based on the powerful sequential quadratic programming (SQP) algorithm has been used in combination with the genetic algorithm (GA) in order to accurately capture the global optimal solutions. At the end, the residual hoop stress distribution and fatigue life of the optimum configurations for each combination of autofrettage and shrink-fit processes have been evaluated and compared.

Enhancing Axisymmetric Compression Testing: Modeling and Addressing Flow Curve Errors

Experimental Methodology for Obtaining the Flow Curve of Sheet Materials in a Wide Range of Strains

A Computationally Efficient Dynamical Model of Fluidic Soft Actuators and Its Experimental Verification

An experimental validation study of a numerical modeling approach to predicting post-consolidation dimensions of thermoplastic composites

Flow curve approximation using Avitzur's model for barreling compression test

Transverse squeeze flow of thermoplastic composite tape during in-situ consolidation via automated fiber placement

Analytical Modeling of Fracture Strain and Experimental Validation in Incremental Sheet Forming

Analysis and Optimization of Autofrettaged and Shrink-Fitted Compound Cylinders under Thermo-Mechanical Loads

Experimental and numerical investigation of combined isotropic-kinematic hardening behavior of sheet metals

Efficient numerical analysis of in-plane compression-induced defects in thick multi-ply woven textile preforms during double diaphragm forming

Determination of Assumed Strain Hardening Relationship from Shear-Compression Model and Data Analysis

An Interactive Fluid–Solid Approach for Numerical Modeling of Composite Metal Foam Behavior under Compression

Progressive failure analysis and taguchi-based optimisation of filament-wound composite tubes subjected to internal pressure using continuum damage mechanics approach

Large Strained Fracture of Nearly Incompressible Hyperelastic Materials: Enhanced Assumed Strain Methods and Energy Decomposition

Combined Composites Layup Architecture and Mechanical Evaluation of Type IV Pressure Vessels: A Novel Analytical Approach

A novel systematic approach for robust numerical simulation of carbon fiber-reinforced plastic circular tubes: Utilizing machine-learning techniques for calibration and validation

A Direct Approach Toward Simulating Cyclic and Non-Cyclic Fatigue Failure of Metals

A Generalized, Computationally Versatile Plasticity Model Framework - Part I: Theory and Verification Focusing on Tension‒compression Asymmetry

Accounting for localized deformation: a simple computation of true stress in micropillar compression experiments

Multi-Scale Experimental Characterization for LS-DYNA MAT213 Modeling of Composite Structures under High Strain Rate

Incorporating point cloud failure criterion in an orthotropic visco-elastic-plastic material model