Abstract:Wearable thermoelectric generators (w-TEGs) convert thermal energy into electrical energy to realize self-powering of intelligent electronic devices, thus reducing the burden of battery replacement and charging, and improving the usage time and efficiency of electronic devices. Through finite element simulation, this study successfully designed high-performance thermoelectric generator and made it into wearable thermoelectric module by adopting “rigid device—flexible connection” method. It was found that higher convective heat transfer coefficient (h) on cold-end leads to larger effective temperature difference (ΔTeff) and better power generation performance of device in typical wearable scenario. Meanwhile, at same h on the cold-end, longer TE leg length leads to larger ΔTeff established at both ends of device, larger device output power (Pout) and open-circuit voltage (Uoc). However, when the h increases to a certain level, optimization effect of increasing TE leg length on device power generation performance will gradually diminish. For devices with fixed temperature difference between two ends, longer TE leg length leads to higher resistance of TEGs, resulting in lower device Pout but slight increase in Uoc. Finally, sixteen 16 × 4 × 2 mm2 TEGs (L = 1.38 mm, W = 0.6 mm) and two modules were fabricated and tested. At hot end temperature Th = 33 °C and cold end temperature Tc = 30 °C, the actual maximum Pout of the TEG was about 0.2 mW, and the actual maximum Pout of the TEG module was about 1.602 mW, which is highly consistent with the simulated value. This work brings great convenience to research and development of wearable thermoelectric modules and provides new, environmentally friendly and efficient power solution for wearable devices.

Flexible Micro Thermoelectric Generator based on Electroplated Bi2Te3

Exploring Material Properties and Device Output Performance of a Miniaturized Flexible Thermoelectric Generator Using Scalable Synthesis of Bi2Se3 Nanoflakes

Bi 2 Te 3 -based flexible thermoelectric generator for wearable electronics

Development of MEMS Process Compatible (Bi,Sb)2(Se,Te)3-Based Thin Films for Scalable Fabrication of Planar Micro-Thermoelectric Generators

Flexible Bi2Te3/PEDOT nanowire sandwich-like films towards high-performance wearable cross-plane thermoelectric generator and temperature sensor array

High-performance flexible wavy-structure thermoelectric generator based on (Bi, Sb)2Te3 films for energy harvesting

Flexible micro thermoelectric generators with high power density and light weight

Stretchable Thermoelectric Generators Based on Bulk Bi2Te3 and Liquid Metals

A High Power Density Micro-Thermoelectric Generator Fabricated by an Integrated Bottom-Up Approach

High-Performance Wearable Bi2Te3-Based Thermoelectric Generator

Achieving High Thermoelectric Performance in Bi2(Te, Se)3 Thin Film with (00 l)-Oriented by Incorporating Tellurization and Selenization Processes

Design of a Wearable Thermoelectric Generator for Harvesting Human Body Energy

Flexible, High-Power Density, Wearable Thermoelectric Nanogenerator and Self-Powered Temperature Sensor

Encapsulated Ag2Se-based Flexible Thermoelectric Generator with Remarkable Performance

A Novel PDMS-Based Flexible Thermoelectric Generator Fabricated by Ag2Se and PEDOT:PSS/Multi-Walled Carbon Nanotubes with High Output Performance Optimized by Embedded Eutectic Gallium–Indium Electrodes

Modeling, properties, and fabrication of a micromachined thermoelectric generator

Fabrication and Performance Simulation of Microscale Thermoelectric Modules Made with Bi2Te3-Based Alloys

Flexible Bi2Te3-based thermoelectric generator with an ultra-high power density

Micro-thermoelectric Generators Based on Through Glass Pillars with High Output Voltage Enabled by Large Temperature Difference

High-Performance W-Doped Bi0.5Sb1.5Te3 Flexible Thermoelectric Films and Generators

Flexible power generators by Ag2Se thin films with record-high thermoelectric performance