Abstract:Novel super toughened bioplastics are developed through controlled reactive extrusion processing, using a very low content of modifier, truly a new discovery in the biodegradable plastics area. The super toughened polylactide (PLA) blend showing a notched impact strength of ∼1000 J/m with hinge break behavior is achieved at a designed blending ratio of PLA, poly(butylene succinate) (PBS), and poly(butylene adipate-<i>co</i>-terephthalate) (PBAT), using less than 0.5 phr peroxide modifier. The impact strength of the resulting blend is approximately 10 times that of the blend with the same composition without a modifier and ∼3000% more than that of pure PLA. Interfacial compatibilization among the three biodegradable plastics took place during the melt extrusion process in the presence of a controlled amount of initiator, which is confirmed by scanning electron microscopy and rheology analysis. The synergistic effect of strong interfacial adhesion among the three blending components, the decreased particle size of the most toughened component, PBAT, to ∼200 nm, and its uniform distribution in the blend morphology result in the super tough biobased material. One of the key fundamental findings through the in situ rheology study depicts that the radical reaction initiated by peroxide occurs mainly between PBS and PBAT and not with PLA. Thus, the cross-linking degree can be controlled by adjusting renewable sourced PLA contents in the ternary blend during reactive extrusion processing. The newly engineered super toughened PLA with high stiffness and high melt elasticity modulus could reasonably serve as a promising alternative to traditional petroleum plastics, where high biobased content and biodegradability are required in diverse sustainable packaging uses.

Toward the production of bioblends for the automotive sector: Reuse of recycled polyamide 6,6 to prepare super‐tough biopolyethylene

Toward the reuse of styrene–butadiene (SBRr) waste from the shoes industry: production and compatibilization of BioPE/SBRr blends

Reactive processing of PA6/EPDM‐MA blends as modifier for application and development of high‐performance polypropylene

Highly toughened PA6 using residue of plasticized PVB film via two-step reactive melt blending

Highly toughened poly(lactic acid) blends prepared by reactive blending with a renewable poly(ether‐block‐amide) elastomer

Repurposing ABS to Produce Polyamide 6 (PA6)-Based Blends: Reactive Compatibilization with SAN-g-MA of a High Degree of Functionalization

Mechanical recycling of polyamide 6 and polypropylene for automotive applications

EPDM‐g‐MAH Toughened Bio‐based Polyamide 56 to Prepare Thermoplastic Polyamide Elastomer and the Performance Characterization

Fabrication of biopolyethylene-based biocomposites with coffee ground waste: Effect of polyethylene-graft-maleic anhydride

A Promising Recycling Strategy via Processing Polypropylene/Recycled Poly(ethylene terephthalate): Reactive Extrusion Using Dual Compatibilizers

From Waste Vegetable Oil to a Green Compatibilizer for HDPE/PA6 Blends

Production of Thermoplastic Elastomers Based on Recycled PE and Ground Tire Rubber: Morphology, Mechanical Properties and Effect of Compatibilizer Addition

Toward Producing Biopolyethylene/Babassu Fiber Biocomposites with Improved Mechanical and Thermomechanical Properties

Morphological, Thermal, and Mechanical Characterization of Bio-Based High-Density Polyethylene / Biopolyamide 6.10 Blends Compatibilized with PE and SEBS Functionalized With Maleic Anhydride

High-strength and super-tough PA6/PS/PP/SEBS quaternary blends compatibilized by using a highly effective multi-phase compatibilizer: Toward efficient recycling of waste plastics

Preparation and characterization of a sustainable foamed biocomposite from compatibilized recycled polyethylene and agave fiber

Recycling Polyethylene/Polyamide Multilayer Films with Poly(isoprene-g-Maleic Anhydride) Compatibilizer

Super Toughened Poly(lactic acid)-Based Ternary Blends via Enhancing Interfacial Compatibility

Enhancement and Compatibilization of Waste-Sourced Biocomposites Through Elastomer Blending and Matrix Grafting Modification

Stable nanoscale sea-island structure of biobased polyamide 56/poly (butylene adipate- co -terephthalate) blends compatibilized by interfacial hyperbranched structure: Toward biobased polymer blends with ultrahigh toughness

Invention of biobased polymer alloys and their application in plastic automobile parts