Abstract:Interpenetrating phase composites (IPCs) with porous metal materials as the matrix and polymer materials as the reinforcement, which have a broad application prospect, have both the high strength of metal materials and the high energy absorption capacity of polymer materials. Entangled metallic wire materials are a new type of porous material with damping characteristics, which is an excellent choice for use as the matrix of IPCs. In the present work, a novel entangled metallic wire material–silicone rubber IPC is developed through the vacuum infiltration method with the entangled wire material as the matrix and silicone rubber as the reinforcing element. The mechanical properties (loss factor and tangent modulus) of the as-synthesized composites are characterized through compression tests. More specifically, the effects of key experimental parameters (strain) and material properties (matrix density, wire diameter, and anisotropy) on the mechanical properties of the composites are analyzed in detail. It is found that with the introduction of interfacial friction, the loss factor of the composites becomes higher than those of the pure entangled metallic wire material and silicone rubber; in particular, the tangent modulus is significantly enhanced. The complex structural characteristics of the proposed composite enable the loss factor and tangent modulus to exhibit a nonlinear relationship with the density over a range of displacement values. Moreover, the smaller the wire diameter is, the greater the loss factor of the composites is, while the tangent modulus exhibits the opposite trend. The unique wire contact form and preparation process endow the composites with nonlinear properties in the molding direction as well as pronounced anisotropy characteristics. A novel interpenetrating phase composite is proposed. The composite quasistatic curve is nonlinear with excellent mechanical properties. The improved energy consumption properties are due to the interfacial friction. The increase in wire density greatly improves the elastic modulus of the composite. The composite is anisotropic with a better bearing capacity in the molding direction.

A ZA22/Al interpenetrating phase composite with high compressive stress plateau and high damping capacity

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Development of Interpenetrating Phase Structure AZ91/Al2O3 Composites with High Stiffness, Superior Strength and Low Thermal Expansion Coefficient

High damping capacity of AlSi10Mg-NiTi lattice structure interpenetrating phase composites prepared by additive manufacturing and pressureless infiltration

Enhanced mechanical and thermal properties in 3D printed Al 2 O 3 lattice/ epoxy interpenetrating phase composites

Anisotropic Dry Sliding Friction and Wear Properties of a Novel Stainless Steel/ZA8 Alloy Interpenetrating Phase Composite Produced by Squeeze Casting

Compressive and flexural properties and damage modes of aluminum foam/epoxy resin interpenetrating phase composites reinforced by silica powder

Mechanical behavior of entangled metallic wire mesh–silicone rubber interpenetrating phase composites under quasistatic compression

Multi-directional freeze-casting of interpenetrating phase composites with multi-aligned structure, nearly isotropy, high performance

Compressive Properties and Failure of Aluminum/Epoxy Resin Interpenetrating Phase Composites Reinforced by Glass Fiber

Tensile properties and damage mechanisms of 3D printed Ti-24Nb-4Zr-8Sn alloy and polyurea interpenetrating phase composites

Fabrication and properties of Si/Al interpenetrating phase composites for electronic packaging

An Al-Al interpenetrating-phase composite by 3D printing and hot extrusion

Interpenetrating Phase Composite Foam Based on Porous Aluminum Skeleton for High Energy Absorption

Interfacial research on interpenetrating network structure ZrO2/Al-Mg composites prepared by Extrusion Freeform Fabrication 3DP and pressureless infiltration

Investigation of Multi-Phase Intermetallic Matrix Composites (IMC) Based on Al–Mo–Zr–Co System

The Making of Metal-Matrix Interpenetrating Phase Composites by Squeeze Casting

Metal-matrix Interpenetrating Phasecomposites Produced by Squeeze Casting

Metal-matrix interpenetrating phase composite and its in situ fracture observation

Microstructure and properties of a HIP manufactured SiC p reinforced high alloyed Al–Zn–Mg–Cu–Zr–Ti aluminum matrix composite

Polymer/metal Interpenetrating Phase Composites Prepared Via Γ‐ray Initiated In‐situ Emulsion Polymerization