Abstract:Interpenetrating phase composites (IPCs) with porous metal materials as the matrix and polymer materials as the reinforcement, which have a broad application prospect, have both the high strength of metal materials and the high energy absorption capacity of polymer materials. Entangled metallic wire materials are a new type of porous material with damping characteristics, which is an excellent choice for use as the matrix of IPCs. In the present work, a novel entangled metallic wire material–silicone rubber IPC is developed through the vacuum infiltration method with the entangled wire material as the matrix and silicone rubber as the reinforcing element. The mechanical properties (loss factor and tangent modulus) of the as-synthesized composites are characterized through compression tests. More specifically, the effects of key experimental parameters (strain) and material properties (matrix density, wire diameter, and anisotropy) on the mechanical properties of the composites are analyzed in detail. It is found that with the introduction of interfacial friction, the loss factor of the composites becomes higher than those of the pure entangled metallic wire material and silicone rubber; in particular, the tangent modulus is significantly enhanced. The complex structural characteristics of the proposed composite enable the loss factor and tangent modulus to exhibit a nonlinear relationship with the density over a range of displacement values. Moreover, the smaller the wire diameter is, the greater the loss factor of the composites is, while the tangent modulus exhibits the opposite trend. The unique wire contact form and preparation process endow the composites with nonlinear properties in the molding direction as well as pronounced anisotropy characteristics. A novel interpenetrating phase composite is proposed. The composite quasistatic curve is nonlinear with excellent mechanical properties. The improved energy consumption properties are due to the interfacial friction. The increase in wire density greatly improves the elastic modulus of the composite. The composite is anisotropic with a better bearing capacity in the molding direction.

Tensile properties and damage mechanisms of 3D printed Ti-24Nb-4Zr-8Sn alloy and polyurea interpenetrating phase composites

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

Enhanced mechanical and thermal properties in 3D printed Al 2 O 3 lattice/ epoxy interpenetrating phase composites

Mechanical properties of 3D printed interpenetrating phase composites with TPMS architectures

Mechanical Performance of 3D Printed Interpenetrating Phase Composites with Spinodal Topologies

Mechanical behavior of entangled metallic wire mesh–silicone rubber interpenetrating phase composites under quasistatic compression

On the damage tolerance of 3-D printed Mg-Ti interpenetrating-phase composites with bioinspired architectures

A novel composites of laser 3D printed CoCrFeNiMn/Ti6Al4V lattice structure with B 4 C/AlSi 10 Mg interpenetrating phases

Mechanical behavior of interpenetrating phase composite structures based on triply periodic minimal surface lattices

Mechanical performance of PEEK-Ti6Al4V interpenetrating phase composites fabricated by powder bed fusion and vacuum infiltration targeting large and load-bearing implants

Compressive Properties and Failure of Aluminum/Epoxy Resin Interpenetrating Phase Composites Reinforced by Glass Fiber

Compressive deformation and damage of Mg-based metallic glass interpenetrating phase composite containing 30–70 vol% titanium

Strength-ductility synergy in 3D-printed (TiB + TiC)/Ti6Al4V composites with unique dual-heterogeneous structure

Interpenetrating Phase Composite Foam Based on Porous Aluminum Skeleton for High Energy Absorption

Compressive and flexural properties and damage modes of aluminum foam/epoxy resin interpenetrating phase composites reinforced by silica powder

Mode I/II cracking behavior of additively manufactured interpenetrating phase composites (IPC), an experimental and theoretical study

Unprecedented Strength Enhancement Observed in Interpenetrating Phase Composites of Aperiodic Lattice Metamaterials

Anisotropic Dry Sliding Friction and Wear Properties of a Novel Stainless Steel/ZA8 Alloy Interpenetrating Phase Composite Produced by Squeeze Casting

Study on the microstructure and mechanical properties of Ti-Zr-Cu-Ni amorphous filler brazed Inconel 718 and 3D printed TC4 alloy

Tensile behaviors of nanoporous phenolic composites reinforced by 3D needle-punched preforms with different weave patterns

3D printed Mg-NiTi interpenetrating-phase composites with high strength, damping capacity, and energy absorption efficiency