Abstract:As humanity is confronted by climate change, electrochemical CO 2 reduction has become an important strategy for generating value-added chemicals whilst lowering carbon emissions. In this work, Cu 2 O nanoparticles with different morphologies and predominant exposed crystal facets, including nanocubes (Cu 2 O-NC) with (100) facets, nanoflowers (Cu 2 O-NF) with (110) facets, and octahedral structures (Cu 2 O-O) with (111) facets, are prepared, and compared as catalysts for the electrochemical CO 2 reduction to C 2+ products in a flow cell electrolyzer, to overcome the mass transfer limitations of CO 2 in an H-cell and reach industrially relevant currents. To maximize the performance towards C 2+ products, a parameter optimization ( i.e. pH and current) was performed. Under the conditions of 150 mA cm −2 and pH of 8.5, the Cu 2 O-NC revealed a maximum faradaic efficiency of 58% for C 2+ products. Similar studies in an H-cell system have shown lower total C 2+ FE of around 35–40% for the nanocubes, indicating an improvement and showcasing the advantages of using a gas-fed flow electrolyzer. Finally, the long-term stability of these materials was also evaluated. The results revealed that C 2+ activity remains constant for four hours at 50%. However, a sharp decline was observed after five hours when GDE flooding occurs, leading to a dominant HER. To confirm, the electrode was washed and dried before re-utilizing it. Since the Cu 2 O largely recovers its initial C 2+ activity (from 50% to 43%) albeit with a slightly different product composition, this confirms GDE flooding as the main cause of degradation. During the eCO 2 RR, Cu 2 O is reduced to metallic Cu, as proven by in situ Raman. As a result, the particle morphology is roughened, which is proven by ex situ SEM images. Subsequently, water penetrates the gas diffusion electrode more easily, inhibiting the diffusion of CO 2 , and alongside the electrowetting effect results in GDE flooding. In conclusion, this work explores the utilization of different Cu 2 O catalysts in a flow electrolyzer, revealing insights into higher currents, their stability issues, crystal facet dependency, and reaction environment, which was unexplored in previous literature where the focus was on H-cell testing, which evaluates the catalysts under less demanding and more controlled conditions that are less relevant for up-scaling and eventual commercialization. Based on these new insights, further improvements can be made to enhance the total C 2+ FE and improve stability.

Micro/Nano‐Structured Superhydrophobic Gas Diffusion Electrode for Boosting the Stability of Industrial‐Compatible Electrochemical CO Production in Flow Cells

Hydrophobized electrospun nanofibers of hierarchical porosity as the integral gas diffusion electrode for full-pH CO2 electroreduction in membrane electrode assemblies

Antiflooding Gas Diffusion Electrodes Enabled by Liquid-Solid-Liquid Interfaces for Durable CO2 Electrolysis

Precise Site-Hydrophobicity Modulation for Boosting High-Performance CO 2 Electroreduction

Hierarchically Conductive Electrodes Unlock Stable and Scalable CO2 Electrolysis

From batch to flow: the effect of pH, current, and the crystal facets of Cu2O on electrochemical CO2 reduction

Gas diffusion enhanced electrode with ultrathin superhydrophobic macropore structure for acidic CO 2 electroreduction

Gas Diffusion Electrodes (GDEs) for Carbon Dioxide (CO 2 ) Reduction in Microfluidic Cells: Towards a Fluid Dynamics Assisted Rational Design

Surface coating combined with in situ cyclic voltammetry to enhance the stability of gas diffusion electrodes for electrochemical CO2 reduction

Pore accessibility matters in CO 2 electrolysis: Preventing H 2 formation and boosting triple-phase boundary on microtubular gas-diffusion electrodes

Self-supported copper-based gas diffusion electrodes improve the local CO2 concentration for efficient electrochemical CO2 reduction

Advances and Challenges of Carbon‐Free Gas‐Diffusion Electrodes (GDEs) for Electrochemical CO2 Reduction

Hydrophobicity Graded Gas Diffusion Layer for Stable Electrochemical Reduction of CO2

Converting CO 2 to multi-carbon products at >1 A/cm 2 using gas diffusion electrode based on commercial materials via transfer process engineering

Hydrophobic 1-octadecanethiol functionalized copper catalyst promotes robust high-current CO2 gas-diffusion electrolysis

Porous Bilayer Electrode‐Guided Gas Diffusion for Enhanced CO 2 Electrochemical Reduction

Cu hollow fiber with coaxially grown Bi nanosheet arrays as an integrated gas-penetrable electrode enables high-current-density and durable formate electrosynthesis

Hollow fiber gas-diffusion electrodes with tailored crystal facets for tuning syngas production in electrochemical CO 2 reduction

Engineering interfacial molecular interactions on Ag Hollow fibre gas diffusion electrodes for high efficiency in CO2 conversion to CO

Impact of gas diffusion layer architecture on the performances of Cu-based electrodes for CO 2 electroreduction to ethylene in flow reactors

Gas diffusion in catalyst layer of flow cell for CO2 electroreduction toward C2+ products