Abstract:The objective of the LuFo VI-1 project CATeW (Coupled Aerodynamic Technologies for Aircraft Wings) consists in multifidelity analyses to assess the potential for aerodynamic efficiency increase by combined application of hybrid laminar flow control and variable camber technologies to the wing of a transonic transport aircraft. Individually, both technologies have proven to lead to major aerodynamic drag reductions. An evaluation of the coupled technologies is, therefore, expected to show an even higher potential due to synergy effects. To derive conclusions on system level, low-fidelity (LowFi) overall aircraft design methodologies will be applied for the analysis of a medium haul reference aircraft in the course of the project, while complex aerodynamic phenomena are modelled with high-fidelity (HiFi) computational fluid dynamics methods. The paper at hand presents results of aerodynamic analyses on both fidelity levels for the wing of the turbulent reference configuration CATeW-01, featuring the technology combination as a retrofit. Furthermore, this work encompasses adaptations and implementations performed within both the LowFi and HiFi toolchains. The LowFi toolchain already incorporates several modules for the proposed technology combination. A short presentation of the LowFi-toolchain is given, along with the modeling approach in the HiFi framework using mesh deformations and a mass flux boundary condition. Comparative studies of the turbulent flow field around the wing show good agreement of predicted load distributions in both numerical frameworks, studies based upon the HiFi approach attest the potential for efficiency increase due to the variable camber technology, incorporated by means of Adaptive Dropped Hinge Flap (ADHF) deflections. Considering the coupled application, four different constant suction mass flow rates are examined, where the maximum mass flow causes laminar flow extending over the entire suction panel, thus moving the transition location from the wing's leading edge to the end of the suction panel. When being coupled with ADHF deflections, again the variable camber technology leads to a reduction of the wing's pressure drag component with the simultaneous application of boundary layer suction further promoting drag reduction with increasing suction rate. While the combined application shows no mutual inhibition, major reciprocal effects are not directly observable when applying the combination as a retrofit to the reference configuration CATeW-01. This is mainly attributed to the limited extend of laminar flow, thus indicating the necessity for optimization in wing geometry and operating parameters, to achieve extensive areas of laminar flow and to promote the aspired synergy effects.

A New Grid-Slat Fusion Device to Improve the Take-Off and Landing Performance of Amphibious Seaplanes

Optimization and Analysis of a Blown Flap Based on a Multielement Airfoil

Computational fluid dynamics-based design optimization of water scooping system in amphibious aircraft by a parallel active learning surrogate model

The analysis of Gurney flap applications for autonomous underwater gliders

Surrogate-based aerodynamic shape optimization of a sliding shear variable sweep wing over a wide Mach-number range with plasma constraint relaxation

Aerodynamic characteristic of wind turbine with the leading edge slat and Microtab

Numerical analyses of a reference wing for combination of hybrid laminar flow control and variable camber

A Study of Multi-Objective Aerodynamic Optimization Design for Variable Camber Airfoils and High Lift Devices

Experimental Validation of a Passive-Adaptive Slat Concept and Characterization under Sinusoidal Fluctuations in the Angle of Attack

Design optimization of a morphing winglet for all flight missions of a civil aircraft

Fluidic Flow Control Devices for Gust Load Alleviation

Hydrodynamic performance improvement on the hydrofoil using slotted configurations

On the drag reduction of an inclined wing via microstructures with the immersed boundary-lattice Boltzmann flux solver

Noise Control for High-Lift Devices by Slat Wall Treatment

Passive separation control of a NACA0012 airfoil via a flexible flap

Wing design optimization and stall analysis with Co-flow Jet active control

Aerodynamic Optimization of a High-Lift System with Adaptive Dropped Hinge Flap

Improved Performance of an Underwater Glider with Passively Rotatable Wings

Computational Investigations for the Feasibility of Passive Flow Control Devices for Enhanced Aerodynamics of Small-Scale UAVs

Hydrodynamic performance optimization and experimental verification of underwater glider based on parametric method

Design of a morphing leading edge as a high lift device for a regional aircraft