Abstract:As a result of increasing energy demands and accelerated environmental problems, there is an urgent need to improve the thermal efficiency of ultra supercritical (USC) power plants. To achieve this goal, advanced ultra-supercritical (A-USC) technologies with the main steam temperature of 700 similar to 750 degrees C and pressure of 35 MPa have been developed quickly in recent years. One of the most promising candidate Ni-based superalloys for the main steam pipe of 700 degrees C ultra-supercritical coal-fired power plants is Inconel 740H, which is a modified version of Inconel 740 developed by Special Metals Corp (SMC). Compared with IN740, the Ti/Al ratio in IN740H is lowered in order to stabilise the microstructure at long ageing times. In addition, the Nb content is lowered to improve the weldability. In this work, the microstructure evolutions, the nucleation and propagation mechanisms of microcracks in the nickel base superalloy Inconel 740H at 750 degrees C high temperature were studied by the self-developed in situ high temperature tensile stage inside a SEM. The results showed that under the uniaxial tensile stress at 22 degrees C room temperature and 750 degrees C high temperature conditions, the grain boundaries of Inconel 740H alloy are al-ways the most primary crack sources. The strength of grain boundaries is higher than that of grains under the room temperature, and the microcracks will be nucleated at the grains as well, but the relative strength of grain boundaries will be weaken under the high temperature, which makes the microcracks tend to nucleate at grain boundaries. The experimental results also showed that the influence of high temperature on the mechanical properties is very significant, the high temperature reducing the activate energy of slip and weakening the strength of the grain boundaries, so that more slip systems activated and the grain boundaries occurring bending and sliding deformation, so further enhance the ability of plastic deformation of alloy. However, the reduction of relative strength of alloy grain boundaries leads to microcracks nucleation and propagation more easily from grain boundaries and lower the yield strength and tensile strength of alloy.

In Situ Microstructural Evolution and Precipitate Analysis of High-Nickel Shipbuilding Steel Using High-Temperature Confocal Laser-Scanning Microscopy

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

In Situ Observation of Bainite to Austenite Transformation of Microalloyed High Strength Steel During Simulated Welding Cycle

Microstructural Evolution of Wrought-Nickel-Based Superalloy GH4169

The Effect of Inclusions on a Medium Temperature Transformation Microstructure and Toughness of High-Strength HSLA Steel

Microstructural Evolution, Nanoprecipitation Behavior and Mechanical Properties of Selective Laser Melted High-Performance Grade 300 Maraging Steel

In-situ investigation of microstructure-dependent deformation behavior of an electron-beam welded Ni Co based superalloy

In-Situ Observation of Ni-11.5wt%Si Eutectic Microstructure Evolution and Exploration of Strengthening Mode of Ni-Ni3si Eutectic Composites

The In Situ Observation of Phase Transformations During Intercritical Annealing of a Medium Manganese Advanced High Strength Steel by High Energy X-Ray Diffraction

In Situ Study of Precipitates' Effect on Grain Deformation Behavior and Mechanical Properties of S31254 Super Austenitic Stainless Steel

Microcrack Nucleation and Propagation Investigation of Inconel 740H Alloy under in Situ High Temperature Tensile Test

Modelling of Microstructure Evolution During Hot Rolling of a High-Nb HSLA Steel

High-resolution Transmission Electron Microscopy Characterization of the Structure of Cu Precipitate in a Thermal-aged Multicomponent Steel

Investigation of Intrinsic Correlation Between Microstructure Evolution and Mechanical Properties for Nickel-Based Weld Metal

Investigating the Role of TiC Precipitation in Dynamic Recrystallization Behavior of a Novel Ship Steel

Effect of Welding Thermal Treatment on the Microstructure and Mechanical Properties of Nickel-Based Superalloy Fabricated by Selective Laser Melting

Microstructure Impacts on Mechanical Properties in a High Temperature Austenitic Stainless Steel

Study of Microstructure of Nickel-Based Superalloys at High Temperatures

On the Microstructure of Heat-Treated Austenitic Nickel-Base Alloy

In Situ Observation of Phase Transformation and Structure Evolution of a 12 Pct Cr Ferritic Stainless Steel

In Situ Scanning Electron Microscopy Analysis of Effect of Temperature on Small Fatigue Crack Growth Behavior of Nickel-Based Single-Crystal Superalloy