Abstract:Power conversion efficiency (PCE) of organic solar cells (OSCs) has reached the threshold for application. However, the high PCEs are mostly obtained from the small‐area OSCs processed by the halogenated solvent, such as chloroform (CF), because the high‐performance A‐DA'D‐A type small molecule acceptors (SMAs) need the CF processing for suitable solubility and rapid solvent evaporation to get appropriate aggregation morphology. Herein, we synthesized two new A‐DA'D‐A type SMAs of Y6‐Ph and L8‐Ph by introducing a phenyl end group in the branched alkyl inner side chains of the representative SMAs Y6 and L8‐BO respectively, for overcoming the excessive aggregation of SMAs in the long‐time film‐forming process in the nonhalogenated solvent processing. Firstly, we studied the effect of the processing solvent boiling point on the aggregation property and photovoltaic performance of the four SMAs of Y6, L8‐BO, Y6‐Ph and L8‐Ph, by using the most commonly used halogenated processing solvents: low‐boiling‐point CF (rapid film forming process) and high‐boiling‐point chlorobenzene (CB) (slow film forming process) for device fabrication of the OSCs with PM6 as polymer donor. It was found that the Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCEs from CF‐ to CB‐processed devices owing to the large phase separation in the CB‐processed OSCs. On the contrary, the devices based on Y6‐Ph and L8‐Ph with the phenyl ending inner side chains show obviously increased PCEs for the OSCs processed by high‐boiling‐point CB. The L8‐Ph‐based devices processed by CB demonstrated an PCE of 18.83% with a high FF of 80.55%, which is even better than the L8‐BO‐based OSCs processed by CF. Furthermore, the L8‐Ph‐based OSCs processed by nonhalogenated solvent o‐xylene (o‐XY) also achieved a high PCE of 18.40% with an FF of 80.11%, which is the best‐performed OSC fabricated from the nonhalogenated solvents so far. In addition, the large‐area (1 cm2) OSCs based on PM6:L8‐Ph processed by o‐XY also demonstrated a higher PCE of 16.66%. The results indicate that introducing phenyl end group in the inner side chains is an effective strategy to improve photovoltaic performance of the A‐DA'D‐A SMAs for future application of the OSCs with nonhalogenated solvent processing. This article is protected by copyright. All rights reserved

A‐DA'D‐A Type Pentacyclic Small Molecule Acceptors to exceed 16.5% efficiency by introducing heteroatom into the outer side chain

A-DA'D-A Type Pentacyclic Small Molecule Acceptors to Exceed 16.5% Efficiency by Heteroatom Effect at the Outer Side Chain

Effects of Oxygen Position in the Alkoxy Substituents on the Photovoltaic Performance of A-DA′D-A Type Pentacyclic Small Molecule Acceptors

Regulating the electron‐deficient component in A‐DA 1 D‐A typed small‐molecule acceptors for high‐performance organic solar cells

The effect of alkyl substitution position of thienyl outer side chains on photovoltaic performance of A–DA′D–A type acceptors

Highly Planar Oligomeric Acceptor Enables Efficiency over 18% with Synergistically Enhanced VOC and Light Absorption

Aromatic side chain manipulation in A–DA′D–A type acceptors for organic photovoltaics

Efficient Organic Solar Cells Based on Low-Cost Pentacyclic Fused-Ring Small Molecule Acceptors with a Fill Factor over 80%

A Simple Phenyl Group Introduced at the Tail of Alkyl Side Chains of Small Molecular Acceptors: New Strategy to Balance the Crystallinity of Acceptors and Miscibility of Bulk Heterojunction Enabling Highly Efficient Organic Solar Cells.

Synergetic alkoxy side‐chain and chlorine‐contained end group strategy toward high performance ultra‐narrow bandgap small molecule acceptors

Dithienobenzothiadiazole-Bridged Nonfullerene Electron Acceptors for Efficient Organic Solar Cells

Efficient Polymer Solar Cells Enabled by A-DA′D-A Type Acceptors with Alkoxypheny-Substituted Quinoxaline As the Fused-Ring Core

A-DA′D-A Type Acceptor with a Benzoselenadiazole A′-Unit Enables Efficient Organic Solar Cells

Modulating Energy Level on an A‐D‐A′‐D‐A‐Type Unfused Acceptor by a Benzothiadiazole Core Enables Organic Solar Cells with Simple Procedure and High Performance

Modulation of Alkyl Chain Length on the Thiazole Side Group Enables Over 17% Efficiency in All‐Small‐Molecule Organic Solar Cells

Medium bandgap A-DA'D-A type small molecule acceptors prepared by synergetic modification strategy for efficient indoor organic photovoltaic devices

Introducing Phenyl End Group in The Inner Side Chains of A‐Da'd‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

A-DAD-A Type Acceptor with a Benzoselenadiazole A-Unit Enables Efficient Organic Solar Cells

Introducing thiazole units into small-molecule acceptors for efficient non-fullerene organic solar cells

Side-chain engineering of nonfullerene small-molecule acceptors for organic solar cells

Over 18% Binary Organic Solar Cells Enabled by Isomerization of Non-Fullerene Acceptors with Alkylthiophene Side Chains