Abstract:Power conversion efficiency (PCE) of organic solar cells (OSCs) has reached the threshold for application. However, the high PCEs are mostly obtained from the small‐area OSCs processed by the halogenated solvent, such as chloroform (CF), because the high‐performance A‐DA'D‐A type small molecule acceptors (SMAs) need the CF processing for suitable solubility and rapid solvent evaporation to get appropriate aggregation morphology. Herein, we synthesized two new A‐DA'D‐A type SMAs of Y6‐Ph and L8‐Ph by introducing a phenyl end group in the branched alkyl inner side chains of the representative SMAs Y6 and L8‐BO respectively, for overcoming the excessive aggregation of SMAs in the long‐time film‐forming process in the nonhalogenated solvent processing. Firstly, we studied the effect of the processing solvent boiling point on the aggregation property and photovoltaic performance of the four SMAs of Y6, L8‐BO, Y6‐Ph and L8‐Ph, by using the most commonly used halogenated processing solvents: low‐boiling‐point CF (rapid film forming process) and high‐boiling‐point chlorobenzene (CB) (slow film forming process) for device fabrication of the OSCs with PM6 as polymer donor. It was found that the Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCEs from CF‐ to CB‐processed devices owing to the large phase separation in the CB‐processed OSCs. On the contrary, the devices based on Y6‐Ph and L8‐Ph with the phenyl ending inner side chains show obviously increased PCEs for the OSCs processed by high‐boiling‐point CB. The L8‐Ph‐based devices processed by CB demonstrated an PCE of 18.83% with a high FF of 80.55%, which is even better than the L8‐BO‐based OSCs processed by CF. Furthermore, the L8‐Ph‐based OSCs processed by nonhalogenated solvent o‐xylene (o‐XY) also achieved a high PCE of 18.40% with an FF of 80.11%, which is the best‐performed OSC fabricated from the nonhalogenated solvents so far. In addition, the large‐area (1 cm2) OSCs based on PM6:L8‐Ph processed by o‐XY also demonstrated a higher PCE of 16.66%. The results indicate that introducing phenyl end group in the inner side chains is an effective strategy to improve photovoltaic performance of the A‐DA'D‐A SMAs for future application of the OSCs with nonhalogenated solvent processing. This article is protected by copyright. All rights reserved

A-DA′D-A Type Acceptor with a Benzoselenadiazole A′-Unit Enables Efficient Organic Solar Cells

Synergistic Effects of Benzoselenadiazole Core and Alkoxy Side Chain Substitution on the Photovoltaic Performance of Non-Fullerene Acceptors

Modulating Energy Level on an A‐D‐A′‐D‐A‐Type Unfused Acceptor by a Benzothiadiazole Core Enables Organic Solar Cells with Simple Procedure and High Performance

Regulating the electron‐deficient component in A‐DA 1 D‐A typed small‐molecule acceptors for high‐performance organic solar cells

Small-Molecule Acceptor with Unsymmetric Substituents and Fused Rings for High-Performance Organic Solar Cells with Enhanced Mobility and Reduced Energy Losses

A-DA'D-A Type Pentacyclic Small Molecule Acceptors to Exceed 16.5% Efficiency by Heteroatom Effect at the Outer Side Chain

Selenium‐Substitution Asymmetric Acceptor Enables Efficient Binary Organic Solar Cells over 18.3% via Regulating Molecular Stacking and Phase Separation

Benzo[c][1,2,5]thiadiazole-fused pentacyclic small molecule acceptors for organic solar cells

A-D-A small molecule donors based on pyrene and diketopyrrolopyrrole for organic solar cells

Dual-Accepting-Unit Design of Donor Material for All-Small-Molecule Organic Solar Cells with Efficiency Approaching 11%

Alkoxy Side-Chain Engineering of Quinoxaline-Based Small Molecular Acceptors Enables High-Performance Organic Solar Cells

Benzotriazole‐Based Donor‐Acceptor‐Acceptor Electron Donors for Vacuum‐Deposited Small Molecule Organic Solar Cells

A‐DA'D‐A Type Pentacyclic Small Molecule Acceptors to exceed 16.5% efficiency by introducing heteroatom into the outer side chain

Tailoring the Position of Ester Group on N‐Alkyl Chains of Benzotriazole‐based Small Molecule Acceptors for High‐Performance Organic Solar Cells

Wide-Band Gap Small-Molecule Donors with Diester-Terthiophene Bridged Units for High-Efficiency All-Small-Molecule Organic Solar Cells

Ternary solvent-processed efficient organic solar cells based on a new A-DA′D-A acceptor derivative employing the 3rd-position branching side chains on pyrroles

Medium bandgap A-DA'D-A type small molecule acceptors prepared by synergetic modification strategy for efficient indoor organic photovoltaic devices

A novel A-DA'D-A bifunctional small molecule for organic solar cells application with impressive photovoltaic performance

Facile access to high-performance organic solar cells through an A-D1-D2-A type unfused non-fullerene acceptors

Introducing Phenyl End Group in The Inner Side Chains of A‐Da'd‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Designing A‐D‐A Type Fused‐Ring Electron Acceptors with a Bulky 3D Substituent at the Central Donor Core to Minimize Non‐Radiative Losses and Enhance Organic Solar Cell Efficiency