Abstract:Multi-material Laser Beam Powder Bed Fusion (PBF-LB) is a promising approach to meet industrial demands for multifunctional components, due to its enhanced freedom of design. Copper and stainless steel are interesting materials to be combined due to the high electrical and thermal conductivity of copper and the mechanical strength and wear resistance of steel. However, this system suffers from copper contamination cracking (CCC), a phenomenon which leads to intergranular cracking of the steel due to penetration of liquid copper. The more these materials intermix, the greater the amount of copper that can penetrate and damage the steel. Mixing is more intense when steel is below copper during printing, a situation that cannot always be avoided due to design constraints. In this sense, this research tackles the worst scenario of printing CuCrZr onto 316 L and analyses the effect of beam shaping on interface quality. For the first time, a ring-mode laser was applied to multi-material PBF-LB with the goal to reduce intermixing. It was observed that using a ring-mode laser source instead of a Gaussian beam decreases mixing of the two alloys and reduces interface defects, albeit being unable to completely suppress cracking. Grain size and texture were also affected by the beam shape, with the Gaussian beam leading to formation of small equiaxed grains along 20 layers of CuCrZr, resulting in random texture. The ring-mode laser source, on the other hand, yields columnar grains and texture along the build direction. Both beam shapes were observed to induce supercooling below the liquid miscibility gap in the Cu–Fe system. Besides the expected γ-Fe and ε-Cu phases, iron was also found to crystallize in a body-centered cubic (BCC) lattice structure, which is believed to happen due to Ni depletion of the steel in Cu-rich compositions, coupled to insufficient copper within the Fe-rich liquid during solidification. BCC fractions are higher for the Gaussian beam. These differences in microstructure and BCC fraction are attributed to the high intermixing of CuCrZr and 316 L when applying Gaussian beams, which is around 10 times higher than with the ring-mode laser.

Influence of beam diameter on Laser Powder Bed Fusion (L-PBF) process

A Holistic Approach for Evaluation of Gaussian versus Ring Beam Processing on Structure and Properties in Laser Powder Bed Fusion

Effect of laser focal point position on porosity and melt pool geometry in laser powder bed fusion additive manufacturing

Investigation of an Increased Particle Size Distribution of Ti-6Al-4V Powders Used for Laser-Based Powder Bed Fusion of Metals

High power laser powder bed fusion of Inconel 718 alloy: Effect of laser focus shift on formability, microstructure and mechanical properties

Laser powder-bed fusion additive manufacturing: physics of complex melt flow and formation mechanisms of pores, spatter and denudation zones

Effects of beam shaping on copper-steel interfaces in Multi-material Laser Beam Powder Bed Fusion

The influence of novel beam shapes on melt pool shape and mechanical properties of LPBF produced Al-alloy

A Review on Laser Beam Shaping Application in Laser Powder Bed Fusion

Experimental and numerical exploration of defocusing in Laser Powder Bed Fusion (LPBF) as an effective processing parameter

The influence of beam focus during laser powder bed fusion of a high reflectivity aluminium alloy -- AlSi$_{10}$Mg

Fluid and particle dynamics in laser powder bed fusion

Laser Powder Bed Fusion of Powder Material: A Review

Influence of shielding gas flow consistency on parts quality consistency during large-scale laser powder bed fusion

Part geometry and conduction-based laser power control for powder bed fusion additive manufacturing

The interplay between vapour, liquid, and solid phases in laser powder bed fusion

Effect of bimodal size distribution on the behavioural properties of powders used in the LPBF process

Influence of powder size on defect generation in laser powder bed fusion of AlSi10Mg alloy

An investigation into the effect of CoCrMo powder characteristics on the powder bed density in laser-based powder bed fusion units

Plasma Evolution in Laser Powder Bed Fusion using a Double Pulse Format: Time-resolved Measurements and Physics-based Modeling

Dual-laser powder bed fusion using 450 nm diode area melting and 1064 nm galvo-scanning fiber laser sources