Abstract:Additive manufacturing of Duplex Stainless Steels (DSS) and Super Duplex Stainless Steels (SDSS) has been successfully demonstrated using LPBF in recent years, however, both alloys feature an almost fully ferritic microstructure in the as-built condition due to the fast cooling rates associated with the Laser Powder Bed Fusion (LPBF) process. Blends of DSS and SDSS powders were formulated with austenitic stainless-steel 316L powder, aiming to achieve increased austenite formation during in the LPBF as-built condition to potentially minimize the post heat treatments (solution annealing and quenching). Powder characteristics were investigated and process parameters were optimized to produce near fully dense parts. Nanoindentation (NI) tests were conducted to measure, not only the local mechanical properties and correlate them with the as-built microstructure, but also to gain a deeper understanding in the deformation behavior of individual phases that cannot be studied directly by macroscopic tensile tests. Scanning Electron Microscopy (SEM) and Electron Backscatter Diffraction (EBSD) were employed for microstructural analysis and phase quantification. The microstructural analysis and EBSD phase maps revealed an increase in austenite in the as-built microstructures. Blend 1 resulted in a duplex microstructure consisting of 10% austenite at the XY plane and 20% austenite at the XZ plane. The austenite content increased with increasing proportion of 316L stainless steel in the powder blends. The DSS blend required a much higher volumetric energy density for the fabrication of near fully dense parts. This imposed a slower solidification and a higher melt pool homogeneity, allowing for adequate diffusion of the austenite stabilizing elements. The presented workflow and findings from this study provide valuable insights into powder mixing for the development of custom alloys for rapid material screening in LPBF.

Effect of bimodal size distribution on the behavioural properties of powders used in the LPBF process

Influence of particle morphology and size distribution on the powder flowability and laser powder bed fusion manufacturability of Ti-6Al-4V alloy

Investigation of an Increased Particle Size Distribution of Ti-6Al-4V Powders Used for Laser-Based Powder Bed Fusion of Metals

An investigation into the effect of CoCrMo powder characteristics on the powder bed density in laser-based powder bed fusion units

The Influence of Powder Particle Size Distributions on Mechanical Properties of Alloy 718 by Laser Powder Bed Fusion

Effect of particle size distribution on the structure and mechanical properties in the process of laser powder bed fusion

Powder preparation during ball milling and laser additive manufacturing of aluminum matrix nanocomposites: Powder properties, processability and mechanical property

Influence of the particle size distribution of monomodal 316L powder on its flowability and processability in powder bed fusion

Predicting the chemical homogeneity in laser powder bed fusion (LPBF) of mixed powders after remelting

Influence of beam diameter on Laser Powder Bed Fusion (L-PBF) process

The interplay between vapour, liquid, and solid phases in laser powder bed fusion

Effect of Particle Size Distribution on the Printing Quality and Tensile Properties of Ti-6Al-4V Alloy Produced by LPBF Process

Numerical Investigation into the Effect of Different Parameters on the Geometrical Precision in the Laser-Based Powder Bed Fusion Process Chain

Powder coarsening mechanisms of Ti-6Al-4 V with multiple build cycles in laser powder bed fusion

Influence of powder size on defect generation in laser powder bed fusion of AlSi10Mg alloy

Role of powder particle size on laser powder bed fusion processability of AlSi10mg alloy

Effect of powder particle size distribution on the surface finish of components manufactured by laser powder bed fusion

Coated Metal Powders for Laser Powder Bed Fusion (L-PBF) Processing: A Review

Novel Powder Feedstock towards Microstructure Engineering in Laser Powder Bed Fusion: A Case Study on Duplex/Super Duplex and Austenitic Stainless-Steel Alloys

Particle-based modelling of laser powder bed fusion of metals with emphasis on the melting mode transition