Abstract:Thin features are integral components of most lightweight cellular lattice structures; however, limited studies are carried out to understand their property/quality aspects. This experimental study investigates the influence of powder feedstock size, feature geometry, and process parameters on the property/quality of thin lightweight features fabricated using a laser powder bed fusion additive manufacturing (L-PBF-AM) system. Three different Ti6Al4V powder feedstocks (fine, medium, and coarse) were utilized, and the dimensions of the features were varied in the range of 0.1 to 0.5 mm. The experimental data were analyzed to gain insights into the powder feedstock-geometry-process-property/quality (PGPP/PGPQ) characteristics, which had not been previously explored but are crucial for designing lightweight structures using L-PBF-AM. The results indicated that both powder feedstock size and feature dimension significantly influenced the properties and quality of the fabricated thin features. Additionally, feature type, volumetric energy density, and their interactions exhibited varying effects on geometrical accuracy, porosity, grain size, and flexural properties. Struts showed lower success rates, grain sizes, and dimensional errors but higher mechanical properties compared to walls. However, both features exhibited similar porosity characteristics. Regarding powder feedstock size, smaller powder sizes were found to be advantageous for fabricating lower-dimensional features and improving their mechanical properties. The feature geometry type also significantly influences the final material properties. A notable observation was that the 0.1 mm wall features exhibited the lowest mechanical properties, particularly in terms of yield strength, while the 0.5 mm strut features exhibited lower mechanical properties among the struts. The findings of the study underscored the importance of understanding the compound relationships between powder feedstock, feature geometry, process parameters, and the resulting properties/quality for lightweight features in L-PBF-AM. Further research is necessary to establish the knowledge and understanding of L-PBF-AM thin features and elucidate the PGPP/PGPQ characteristics in greater detail.

Influence of particle morphology and size distribution on the powder flowability and laser powder bed fusion manufacturability of Ti-6Al-4V alloy

Influence of Powder Particle Morphology on the Static and Fatigue Properties of Laser Powder Bed-Fused Ti-6Al-4V Components

Effect of Particle Size Distribution on the Printing Quality and Tensile Properties of Ti-6Al-4V Alloy Produced by LPBF Process

Effects of the process parameters on the formability and properties of Ni54(at.%) Ti alloys prepared by laser powder bed fusion

Powder preparation during ball milling and laser additive manufacturing of aluminum matrix nanocomposites: Powder properties, processability and mechanical property

Laser powder bed fusion additively manufactured thin lightweight Ti6Al4V features: an experimental investigation on the influence of powder feedstock, geometry, and process parameters on property/quality

Role of powder particle size on laser powder bed fusion processability of AlSi10mg alloy

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Reuse of Ti6Al4V Powder and Its Impact on Surface Tension, Melt Pool Behavior and Mechanical Properties of Additively Manufactured Components

Optimization of Laser Based-Powder Bed Fusion Parameters for Controlled Porosity in Titanium Alloy Components

Numerical simulation of melt pool size and flow evolution for laser powder bed fusion of powder grade Ti6Al4V

Effect of Powder Variability on Laser Powder Bed Fusion Processing and Properties of 316L

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism

The effects of specimens geometry on solidification conditions and microstructure formation in laser powder bed fusion fabricated Ti–6Al–4V alloys

Influence of the physicochemical properties of reusable powders on the mechanical properties of Ti6Al4V manufactured via laser powder bed fusion additive manufacturing

Influence of Powder Bed Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Fabricated via Laser Powder Bed Fusion

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

On thermal properties of metallic powder in laser powder bed fusion additive manufacturing

Investigation of an Increased Particle Size Distribution of Ti-6Al-4V Powders Used for Laser-Based Powder Bed Fusion of Metals

Solidification microstructure variations in additively manufactured Ti-6Al-4V using laser powder bed fusion

Unveiling the impact of layerwise laser preheating on microstructure and mechanical response in laser powder bed fusion