Abstract:The significant disparities in physical and chemical properties between aluminum alloy and high-strength steel pose substantial challenges for conventional friction joining techniques. To address this issue, this study proposes a novel approach utilizing inertial friction welding with an interlayer to join these dissimilar materials. A CrCoNi medium entropy alloy sheet was selected as the interlayer due to its intermediate melting point, thermal conductivity, strength, and surface hardness between 6061-T6 aluminum alloy and 42CrMo steel, as well as its high element mixing entropy. These properties were deemed crucial for balancing interface heat generation and regulation the formation of intermetallic compounds. The experimental procedure involved embedding the CrCoNi sheet into the end face of the 6061-T6 aluminum alloy, followed by the application of IFW to join the aluminum alloy with 42CrMo high-strength steel. This investigation focuses on examining the effects of three distinct friction speeds (3800, 4000, and 4200 rpm) on the microstructural characteristics and mechanical properties of the regulating joints with the CrCoNi interlayer. Results demonstrate that the CrCoNi enhances the temperature at the steel-side interface through friction with 42CrMo steel and 6061-T6 aluminum, combined with adjustments in the friction sequence and duration, promoting plastic deformation. The axial transfer of heat creates a temperature gradient at the joint, enabling low-temperature welding on the aluminum side and forming a mechanical interlocking structure at the interface. The diffusion of Cr, Co, and Ni elements regulates the type and thickness of interfacial intermetallic compounds, ultimately enhancing the joint's strength. The thickness of the intermetallic compounds AlNi3, FeAl3, AlCo, and Fe2Al5 formed at the interface is less than 2 μm. A phase transformation occurred at the 42CrMo high-strength steel interface, leading to the formation of numerous needle-like martensites, which increased the Vickers hardness in the welding seam to 763.9 HV. The joint's tensile strength initially increased and then decreased with increasing friction speed, reaching a maximum of 168.7 MPa at 4000 rpm, which is more than 60% of the aluminum alloy base material's tensile strength.

A new strategy of Al 0.1 CoCrFeNi high entropy alloys and Inconel 625 alloys joining technology

Joining of TiAl-based alloy and a Ni-based superalloy with a NiCoFeCuSiB high entropy filler metal

Microstructure and Mechanical Properties of Al0.3CoCrFeNi High-entropy Alloy Joints Brazed Using a FeCoCrNiCu/Ti Composite Interlayer

Microstructural evolution and mechanical properties in the self-propagating brazing joint of Al 0.1 CoCrFeNi HEAs and 304 SS using reactive multilayer nanofoils

High-density Dislocation and Ductile Precipitate Synergistically Reinforced TiAl/Ni-based Superalloy Joint Using Novel Multi-Principal Element Interlayer

Eutectic-reaction brazing of Al<sub>0.3</sub>CoCrFeNi high-entropy alloys using Ni/Nb/Ni interlayers

Microstructure and tensile properties of dissimilar metal joints between FeCoCrNiMn alloy and stainless steel using CoCrNiMn powders as filler material

Obtaining In-Situ Reacted Fe–W–Ni–Cr–Cu High-Entropy Alloy Within the Interlayer of Dissimilar Cf/SiC-GH3536 Joint by Designing Non-High-entropy Cu–Ti–W Composite Filler

Joining SiCf/SiC Composites to Al0.3CoCrFeNi High-Entropy Alloys with a Cu–Ti Filler Alloy: Interfacial Reactions, High-Entropy Effects, and Mechanical Properties

Improving the ductility in laser welded joints of CoCrFeMnNi high entropy alloy to 316 stainless steel

Microstructure and mechanical properties of SiCf/SiC composites/ GH536 superalloy joints brazed with CoFeNiCrCu high-entropy alloy filler

Synergistic Effects of Monel 400 Filler Wire in Gas Metal Arc Welding of CoCrFeMnNi High Entropy Alloy

Brazing SiC Ceramics and Zr with CoCrFeNiCuSn High Entropy Alloy

Interfacial microstructure and mechanical properties of tungsten alloy/steel diffusion bonding joint using CrFeCoNiCu high entropy alloy interlayer

In-situ Eutectic-Reaction Bonding of Al0·3CoCrFeNi High-Entropy Alloys Using Pure Niobium

Enhanced inertia friction welding of aluminum alloy and high-strength steel using CrCoNi interlayer: Microstructural and mechanical characterization

Microstructure and mechanical properties of resistance spot welded dissimilar aluminum/steel joints fabricated using high entropy alloy as interlayer

Interfacial Strengthening Mechanism of C/C/Nb0.74CoCrFeNi2/Nb Brazed Joints: Stress-relieving Effects of the FCC Phase

A promising strategy of multicomponent alloy intermedium for enhancing the mechanical performance of inertia friction welding joints of Inconel 718 alloys

Transient Liquid Phase Bonding of Cast Al0.3CoCrFeNi High-Entropy Alloy Using Ni/Zr/Ni Laminated Foils

Microstructural Evolution and Mechanical Properties of Ti2AlNb/GH99 Superalloy Brazed Joints Using TiZrCuNi Amorphous Filler Alloy