Abstract:Currently there is a growing interest in investigating aluminum alloy-based hybrid composites due to their growing importance in the automotive and aerospace sectors. To enhance the value of this field, an attempt was made to synthesize zirconium diboride (ZrB 2 ) and copper-coated short steel fiber-reinforced LM26 aluminum alloy hybrid composites using stir casting with varying weight percentages of ZrB 2 (2.5, 5, and 10wt%) and copper-coated short steel fiber (5wt% kept constant) for applications requiring a lightweight and high strength, particularly for high-temperature applications. Matrix, fiber-reinforced composite (FRC), and hybrid composite specimens were synthesized using stir casting technique with the process parameters of 750°C for pouring temperature, 10 minutes for stirring time, 650 rpm for stirring speed, and 400°C for preheating temperature of reinforcements. With the use of a wire-cut electrical discharge machine, the specimens were prepared for various tests in accordance with ASTM standards. A complete microstructural (optical microscope and scanning electron microscope) investigation and mechanical property (hardness, tensile properties, and impact strength) evaluation were carried out according to the ASTM standard to comprehend the influence of the reinforcements, and the findings were presented. The optical microscopic images clearly showed that the ZrB 2 and copper-coated short steel fiber reinforcements were uniformly distributed throughout the matrix (LM26 aluminum alloy). The Brinell hardness values increased as the reinforcements were added, reaching a maximum hardness of 152 BHN for the hybrid composite with 15wt% cumulative reinforcement, which is 35.71% higher than the matrix. Compared to matrix alloy, the composite with 15% cumulative reinforcement exhibited a maximum 38.41% improvement in ultimate tensile strength. As further reinforcement is added after 10wt%, yield strength declines to 6.36%, and for the composite with 15wt% of reinforcement, elongation gradually drops to 33.7% as compared to the matrix. The energy absorption of reinforced composites with 5wt% and 15wt% shows a similar percentage decrease of 42.86%, when compared to the matrix. However, a notable decline in ductility was identified for the composites because of the addition of strong reinforcements, while the LM26 alloy retained its ductility. Further, hybrid composites showed poor resistance to impact load due to the incorporation of hybrid reinforcements, and respective fractography showed brittle fracture. The results make it quite evident that the hybrid composites of copper-coated short steel fiber and ZrB 2 -reinforced LM26 aluminum alloy have outstanding mechanical properties, making them a good choice for use in the automobile industry as a newer material.

Enhancing tribo-mechanical and corrosion properties of A383 aluminum matrix composites through stir-cum-squeeze casting with marble dust and hexagonal boron nitride reinforcement

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Enhancing the mechanical, wear and corrosion behaviour of stir casted aluminium 6061 hybrid composites through the incorporation of boron nitride and aluminium oxide particles

Enhancing Aluminum-Based Composite Manufacturing: Harnessing Si3N4 Reinforcement via Stir Casting Technique

Enhanced mechanical and tribological properties of ultrasonically assisted stir-cast AA7075 metal matrix composites in challenging corrosive environments

Fabrication and Mechanical Behaviour Investigation on Aluminium 7075 Boron Carbide and Inconel Alloy 625 Metal Matrix Composite Using Ultra Sonic Stir Casting Method

Investigation on Mechanical Behavior of Al6061- Coconut Shell Ash- Granite Dust Reinforced Hybrid Metal Matrix Composites Manufactured using Stir Casting Technique

Investigation on Mechanical Behavior of LM26 Aluminum Alloy—ZrB2 and Copper-Coated Short Steel Fiber-Reinforced Composites Using Stir Casting Process

A Systematic Review on the Mechanical, Tribological, and Corrosion Properties of Al 7075 Metal Matrix Composites Fabricated through Stir Casting Process

Investigation on the effect of SiC and TiB2 ceramic particles on mechanical and tribological properties of Al7075 hybrid metal matrix composites prepared through conventional stir casting technique

Mechanical and tribological characteristics of boron carbide reinforcement of AA6061 matrix composite

Enhancement in mechanical properties of ceramic reinforced aluminum MMC via stir casting methodology: A review

Evaluation of Mechanical and Wear Properties of Al 5059/B4C/Al2O3 Hybrid Metal Matrix Composites

A Novel Approach in Developing Aluminum Hybrid Green Metal Matrix Composite Material Using Waste Eggshells, Cow Dung Ash, Snail Shell Ash and Boron Carbide as Reinforcements

Analysis and Experimental Investigation of A356 Aluminium Alloy Hybrid Composites Reinforced with Gr-FE3O4-B4C Nanoparticles Synthesised by Selective Laser Melting (SLM)

Synthesis, Mechanical and Tribological Behaviours of Boron Nitride reinforced AA7075 Composites Produced by Stir Casting Technique

Mechanical Properties of Aluminum-4043/Nickel-coated Silicon Carbide Composites Produced via Stir Casting

Microstructural, mechanical, and wear properties of ultrasonic assisted stir casted A356 Alloy/AlN composite

Assessment of mechanical properties of LM13 aluminum alloy hybrid metal matrix composites

Synthesis, Microstructural Investigation, and Mechanical Behavior of AA5083/Boron Nitride Nanocomposite