Abstract:It is widely recognized that the scandium addition to aluminum alloys is an effective way to improve the comprehensive properties. To the present, researchers are concentrated on Al-Mg alloys, for multicomponent Al-Zn-Mg-Cu alloy, the microscopic characterization of the alloy heat treatment has gained a high level of research interest. However, researches on the evolution of precipitate microstructure in controlled plastic deformation combined with the role played by Sc have received scant attention. In the present paper, a micro-alloyed Al-Zn-Mg-Cu-Sc-Zr alloy was prepared by adding 0.2% scandium. Based on mastering the two-stage homogenization treatment in the early stage, the alloy was subjected to equal channel angular extrusion deformation, and subsequently the microstructure, dislocation evolution and precipitation behavior were observed. It is revealed that after second pass deformation, the grains in the deformation-prone zone are obviously shortened by 31% on average along the cross-section direction, compared with the first pass. Following two passes deformation, Al 3 (Sc, Zr), Al 3 Zr and MgZn 2Â phases are formed within grains, inhibiting grain coarsening and recrystallization during deformation. With the introduction of plastic deformation, it is analyzed that the shadow lines with different depths and stacking faults with different structures in the interior of the phase. Also, the overall proportion of the recrystallized structure and substructure of the alloy increases with the increasing deformation. In addition, after secondary deformation, the scandium rich compounds at the trigeminal grain boundary are reduced, while the zirconium rich compounds are significantly increased. Therefore, the different diffusivity of Sc/Zr elements and the combined effect of controlled thermal deformation can be considered to prepare the Al 3 Sc (Al 3 Zr) with core-shell structure in the later stage.

Microstructure evolutions of the Al-Mg and Al-Mg-Sc-Zr alloys during gradient cooling

Evolution of the Microstructure and Microsegregation in Subrapidly Solidified Mg–6Al–4Zn–1.2Sn Magnesium Alloy

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Microstructural evolution and mechanical property of Al–Mg–Mn alloys with various solidification cooling rates

Microstructure Evolution and Mechanical Properties of a Cast and Heat-Treated Al–Li–Cu–Mg Alloy: Effect of Cooling Rate During Casting

Effect of Minor Sc Addition on the Microstructure Evolution of Al–Cu–Li–Mg Alloy During Homogenization with Different Cooling Modes

The microstructure, fracture mechanism and their correlation with the mechanical properties of as-cast Mg-Nd-Zn-Zr alloy under the effect of cooling rate

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy

Microstructures and Properties of Al–Zn–Mg–Mn Alloy with Trace Amounts of Sc and Zr

The Effect of Cooling Rate on Microstructure and Mechanical Properties of the Zr-4Hf-3Nb (wt%) Alloy

Effect of minor Sc and Zr on recrystallization behavior and mechanical properties of novel Al–Zn–Mg–Cu alloys

The Evolution of Unidirectional Solidification Microstructure of the Al-In Monotectic Alloys in High Temperature Gradient

Effect of Cooling Rate on the Solidified Microstructure of Mg-Gd-Y-Zr Alloy

Effects of Zr,Ti and Sc Additions on the Microstructure and Mechanical Properties of Al-0.4Cu-0.14Si-0.05Mg-0.2Fe Alloys

Microstructure and Mechanical Properties of Casting Al-3Li-2Mg-1Zn-0.1Zr Alloys Modified by Sc Additions

Plastic Deformation and Precipitation Characterization of Al-Zn-Mg-Cu Alloy Micro-Alloyed with Sc

Effect of Sc/Zr ratio on the microstructure and mechanical properties of new type of Al–Zn–Mg–Sc–Zr alloys

Morphology evolution and growth mechanism of primary Al3Sc and eutectic Al3Sc in Al-Sc alloys

Effect of Sc and Zr on Microstructure and Mechanical Properties of As‐Cast Al–Li–Cu Alloys

The Evolution and Characterizations of Al3(ScxZr1-x) Phase in Al–Mg-based Alloys Proceeded by SLM