Abstract:Isotropic and anisotropic NdFeB magnets were synthesized by spark plasma sintering (SPS) and SPS+HD (hot deformation), respectively, using melt-spun ribbons as the starting materials. Spark plasma sintered magnets sintered at low temperatures (<700 °C) almost maintained the uniform fine grain structure inherited from rapid quenching. At higher temperatures, due to the local high-temperature field caused by the spark plasma discharge, the grain growth occurred at the initial particle surfaces and the coarse grain zones formed in the vicinity of the particle boundaries. Since the interior of the particles maintained the fine grain structure, a distinct two-zone structure was formed in the spark plasma sintered magnets. The SPS temperature and pressure have important effects on the widths of coarse and fine grain zones, as well as the grain sizes in two zones. The changes in grain structure led to variations in the magnetic properties. By employing low SPS temperature and high pressure, high-density magnets with negligible coarse grain zone and an excellent combination of magnetic properties can be obtained. An anisotropic magnet with a maximum energy product of ∼30 MG Oe was produced by the SPS+HD process. HD at 750 °C did not lead to obvious grain growth and the two-zone structure still existed in the hot deformed magnets. Intergranular exchange coupling was demonstrated in the spark plasma sintered magnets and was enhanced by the HD process, which reduced the coercivity. Good temperature stability was manifested by low temperature coefficients of remanence and coercivity. The results indicated that nanocrystalline NdFeB magnets without significant grain growth and with excellent properties could be obtained by SPS and HD processes.

Production of Mn-Ga Magnets

Recrystallization and magnetic hardening in Mn<inf>1.8</inf>Ga magnet by spark plasma sintering deformation

High Magnetic Performance in MnGa Nanocomposite Magnets

Large Thermal Conductivity and Robust Mechanical Properties of Ni-Mn-Ga/Cu Magnetocaloric Composites Prepared by Spark Plasma Sintering

Bulk Alpha-Fe/Nd2fe14b Nanocomposite Magnets Prepared by the Phase Transition of Amorphous Nd9fe81co3nb1b6 under High Pressure

Microstructure, Magnetism and Critical Behavior of Hot Pressed Ni-Mn-Ga/Al Magnetocaloric Composites with Enhanced Thermal Conductivity and Mechanical Properties

Microstructure and magnetic properties of (Mn54Al46)98C2 magnets fabricated by liquid-phase sintering with the Mn65Ga35 as an additive

Engineering microstructure to improve coercivity of bulk MnBi magnet

Production of Rare-Earth-Free Iron Nitride Magnets (α′′-Fe16N2)

Structure and Properties Evolutions for Hard Magnetic MnAl and MnGa Based Alloys Prepared by Melt Spinning or Mechanical Milling

Properties of bulk magnets prepared by hot pressing using Zn- coated Sm-Fe-N magnetic powder by electrodeposition

Isotropic and Anisotropic Nanocrystalline NdFeB Bulk Magnets Prepared by Binder-Free High-Velocity Compaction and Hot Deformation

Study on properties of MnAlC magnetic powder and bulk

Anisotropic bulk rare-earth-free Mn-Al-(C) magnets prepared under high-stress and large-strain conditions

An Approach To The Bulk Textured Fe81ga19 Rods With Large Magnetostriction

Interplay between Cu and Ga in Optimizing the Microstructure and Coercivity of Nd-Fe-Cu-Ga-B Sintered Magnet

Magnetic phase transition and magneto-caloric effect (MCE) in (Mn0.5Ni0.5)60+Ga40- (x = 3.3, 5.0, and 6.6) alloys

Nd-Fe-B Sintered Magnets with Low Rare Earth Content Fabricated Via Dy71.5Fe28.5 Grain Boundary Restructuring

Effects of intergranular phase on the coercivity for MnBi magnets prepared by spark plasma sintering

Structural Properties and Large Coercivity of Bulk Mn3−xGa (0 ≤ X ≤ 1.15)

Microstructure and Property Evolution of Isotropic and Anisotropic Ndfeb Magnets Fabricated from Nanocrystalline Ribbons by Spark Plasma Sintering and Hot Deformation