Abstract:Abstract The electrodeposition of aluminum on mild steel in a molten salt electrolyte consisting of a mixture of AlCl 3 /NaCl/KCl (weight percent ratio of 80:10:10) was studied. Parametric studies were carried out to evaluate the effect of different parameters such as current density, electrolysis time, and intermediate coating layer on the coating morphology and coating-to-substrate adhesion. The quality and morphology of the coating were investigated using scanning electron microscope (SEM) and x-ray map analyses. The effect of heat treatment of the coated samples on the interface stability and formation of intermetallic compounds at the Al-Fe interface was also investigated. Cross-sectional examination by SEM as well as energy dispersive spectroscopy (EDS) line scan showed that upon annealing at temperatures in the range of 350 °C–550 °C, brittle Fe-Al intermetallic layers were formed at the interface. This shows that high-temperature service conditions can adversely affect the coating properties. The apparent activation energy of the formation of such intermetallic layers was calculated based on thickness measurements on these layers. The optimum conditions for electroplating were determined as current density of 0.022 A.cm −2 and electroplating time of 60 min. Potentiodynamic polarization tests were used to evaluate the corrosion resistance of the samples in 3.5 wt% NaCl solution. Considering the corrosion rate of coated samples which is much lower than the bare substrate, it was concluded that the electrodeposited coatings could efficiently protect the steel substrate against corrosion in corrosive media.

Composition and structure of Ti–Al alloy powders formed by electrochemical co-deposition in KCl–LiCl–MgCl2–TiCl3–AlCl3 molten salt

Electrochemical synthesis of Ti–Al–V alloy by chlorination of Ti2O3 and V2O3 in AlCl3-containing molten chloride salt

Direct electrochemical reduction of low titanium chlorides into titanium aluminide alloy powders from molten eutectic KCl–LiCl–MgCl2

A New Method for Preparing Titanium Aluminium Alloy Powder

Direct Synthesis of Ti-Al Compound Powders by Electrolysis in Molten LiCl-KCl

Electrodeposition of Aluminum Coatings from AlCl3-NaCl-KCl Molten Salts with TMACl and NaI Additives.

Synthesis of Ti powders with different morphologies via controlling the valence state of the titanium ion in KCl-NaCl molten salt

Anodic behavior in AlCl3-EMIC ionic liquid of Ti6Al4V alloy and its application for enhancing the adhesion strength of aluminum coatings

Investigation on the reaction progress of titanium and lead chloride in NaCl-KCl melt

Electrodeposition of aluminum on rare earth alloy surface in room temperature molten salts

Electrochemical extraction of titanium from carbon-doped titanium dioxide precursors by electrolysis in chloride molten salt

Electrodeposition of Aluminum on Aluminum Surface from Molten Salt

Electrochemical Deposition of Al–Mg Alloys on Tungsten Wires from AlCl3–NaCl–KCl Melts

Experimental investigation on the formation mechanism of the TiFe alloy by the molten-salt electrolytic titanium concentrate

Study on the electrochemical behavior of Mg and Al ions in LiCl-KCl melt and preparation of Mg-Al alloy

Electrodeposition of Titanium Aluminide (TiAl) Alloy from AlCl3–BMIC Ionic Liquid at Low Temperature

Electrochemical behavior of Zr(IV) and co-reduction synthesis of Al-Zr alloys in KF-AlF3-Al2O3-ZrO2 molten salt

Electrodeposition of Aluminum on Stainless Steel from Room Temperature Molten Salts

Study on the Initial Electrodeposition Behavior of Aluminum on Tib2/A356 Composite

Electrochemical Formation of Al-Tb Alloys from Tb 4 O 7 Fluorinated by AlF 3 in NaCl-KCl Melts

Molten salt electrodeposition of aluminum on mild steel: effect of process parameters on surface morphology and corrosion properties