Abstract:When the temperature of the package assembly is changed, non‐uniform deformation and local stress may occur owing to the different thermal expansion coefficients of the constituent materials, while concentrated thermal stress may cause significant failure. In this study, we carry out an experiment and analysis of the thermal deformation of a flip chip plastic ball grid array package with respect to temperature change. Interference fringe patterns representing the displacement distribution of each temperature stage are obtained using a Moiré interferometry and the bending deformation behavior and the strain of the solder ball are analyzed thereafter. We compare the deformation behavior of a single‐sided package assembly and a double‐sided package assembly. The effective strain, which significantly affects the failure of the solder ball, is found to be the largest in the solder ball just outside the edge of the chip in the case of the single‐sided package assembly. In the case of the double‐sided package assembly, the maximum effective strain is found in the solder ball just inside the edge of the chip, with a value approximately 50 % larger than in the case of the single‐sided package assembly. Wenn sich die Temperatur eines Gehäuses ändert, kann es aufgrund der unterschiedlichen Wärmeausdehnungskoeffizienten der einzelnen Werkstoffe zu ungleichmäßigen Verformungen und lokalen Spannungen kommen, während konzentrierte thermische Spannungen zu erheblichen Ausfällen führen können. In dieser Studie führen wir ein Experiment und eine Analyse der thermischen Verformung einer Flip‐Chip Kunststoffkugel Gitteranordnung in Abhängigkeit von der Temperaturänderung durch. Mit Hilfe der Moiré‐Interferometrie werden Interferenzstreifenmuster aufgenommen, die die Verschiebungsverteilung jeder Temperaturstufe darstellen und anschließend werden das Biegeverformungsverhalten und die Dehnung der Lötkugel analysiert. Wir vergleichen das Verformungsverhalten einer einseitigen und einer doppelseitigen Gehäusebaugruppe. Es zeigt sich, dass die effektive Dehnung, die das Versagen der Lötkugel maßgeblich beeinflusst, im Fall der einseitigen Baugruppe in der Lötkugel direkt außerhalb des Chiprands am größten ist. Bei der doppelseitigen Baugruppe ist die maximale effektive Dehnung in der Lötkugel direkt innerhalb des Chiprands zu finden, mit einem Wert der etwa 50 % größer ist als bei der einseitigen Baugruppe. In this study, the thermo‐mechanical deformation behavior of flip chip plastic ball grid array packages was analyzed using Moiré interferometry. Interference fringe patterns representing the displacement distribution of each temperature stage were recorded at each temperature stage, and clear fringes were obtained. The bending deformation behavior and the strain of the solder ball are analyzed.

Characterization of flexural and thermo-mechanical behavior of plastic ball grid package assembly using moiré interferometry

Thermo‐mechanical behavior of ball grid packages with different solder ball grid patterns investigated through moiré interferometryThermomechanisches Verhalten von Kugelgitterpackungen mit unterschiedlichen Lotkugelgittermustern, untersucht durch Moiré‐Interferometrie

Simulation and Experimental Analysis of Thermomechanical Stress Around Interconnects for W2W Hybrid Bonding

Comparison between Experimental Measurement and Numerical Analysis of Warpage in PBGA Package and Assembly with the Consideration of Residual Strain in the Molding Compound

Advanced Mechanical/Optical Configuration of Real-Time Moiré Interferometry for Thermal Deformation Analysis of Fan-Out Wafer Level Package

Thermal Deformation Measurement of Electronic Package Using Advanced Moire Methods

Study of Thermal Deformation of Electronic Package Using Scanning Moire Method with High Resolution Microscopy

Deformation behaviors of flip chip plastic ball grid array packages subjected to temperature change using moiré interferometry

High Resolution AFM Scanning Moiré Method and Its Application to the Micro-Deformation in the BGA Electronic Package

Thermal deformation analysis of BGA package by digital image correlation technique

Thermal Deformation Measurement of the Solder Joints in Electronic Packages Using Electron Moiré Method

Thermal Deformation Measurement of Electronic Packaging Component Using Afm Scanning Moire Method

Segmental Orientations and Deformation Mechanism of Poly(Ether-Block-Amide) Films

Warpage measurement and simulation of flip-chip PBGA package under thermal loading

Analysis of warpage and reliability of very thin profile fine pitch ball grid array

Application of Moiré Interferometry to the Characterization of Orthotropic Materials in the Antisymmetric Configuration Using the Virtual Fields Method

Investigation of Long-Term Reliability and Failure Mechanism of Solder Interconnections with Multifunctional Micro-Moiré Interferometry System

Thermally-Induced Deformations and Warpages of Flip-Chip and 2.5D IC Packages Measured by Strain Gauges

Experimental Characterization and Modeling of the Bending Strain Effect on Flexible Microwave Diodes and Switches on Plastic Substrate

Characterization of 2.5D package warpage through Shadow Moiré technique and failure analysis

Modeling of Underfilled PBGA Assemblies Using Both Viscoelastic and Elastic Material Properties