Abstract:Currently, the hot forming of aluminum alloys has garnered significant attention for overcoming poor formability at room temperature (RT). However, the current hot forming technique is facing problems such as time-consuming procedures and high economic cost. To improve forming efficiency, we herein propose a novel forming technique for heat-treatable aluminum alloys, termed pre-aged hardening warm forming (PHF) process. An Al–Zn–Mg–Cu alloy is used to investigate the flow behavior, drawing formability, and post-forming mechanical properties during the aforementioned process. Uniaxial tensile tests and Erichsen tests are conducted to evaluate the plastic flow behavior and drawability, respectively. Stamping tests are performed on a cap beam component to verify the engineering feasibility of the forming technique. Optical microscopy (OM) and transmission electron microscopy (TEM) are performed to characterize the microstructure evolution during the PHF process. The tensile test results show that the pre-aged alloys exhibit true fracture elongation similar to the fracture elongation of the O-temper alloy at RT, and that the Erichsen values of the pre-aged alloys are 5%–16% higher than that of the O-temper alloy at 200 °C. The results of the stamping tests for the cap beam component indicate that the optimal final strength of the stamped component achieves σ/σ0.2 = 566 MPa/500 MPa, exceeding the strength of the AA7075-T6 alloy. OM observations show that the stamping process does not significantly affect the grain sizes of the pre-aged alloys. TEM results show that numerous thermostable GPⅡ zones exist in the pre-aged alloys, and that the stamping procedure transforms the GPⅡ zones to dispersed η′ phases and results in the entanglement of numerous dislocations. The dual effects of phase transformation and plastic deformation during the PHF process contribute to the desirable mechanical properties of the stamped components.

Formability and Numerical Simulation for as-quenched Aluminum Alloy Sheet

Study on Simulation of Stamping Forming and Die Surface Optimization of Aluminum Alloy Plate

Pre-stretching Process and Its Application in Reducing Residual Stress of Quenched 7075 Aluminum Alloy Thick-Plates

Finite Element Method Simulation for Residual Stress in Quenched Aluminum Alloy Thick-Plate and Its Effect on Machining Distortion

Experimental and Numerical Investigation on Strengthening Behavior of 7075 Aluminum Alloy Sheets in Hot Forming–Quenching Integrated Process

The Effect of Hot Forming–Quenching and Heat Treatment Processes on the Mechanical Properties of AA6016 Aluminum Alloy Sheets

Effect of Heat Treatment Conditions on Mechanical Properties and Precipitates in Sheet Metal Hot Stamping of 7075 Aluminum Alloy

The Influence of Cold Forming and Heat Treatment Processes on the Mechanical and Fracture Properties of AA6016 Aluminum Sheets

Comparative study on the formability and microstructure evolution of different tempered Al–Cu–Li alloy sheets during room and cryogenic temperature forming process

Study on hydroforming of AA6061-T6 aluminum alloy sheet based on upper sheet

Numerical Simulation of Quenching and Pre-Stretching Residual Stress in 7085 Aluminum Alloy Plate

Strength and Formability Improvement of Al-Cu-Mn Aluminum Alloy Complex Parts by Thermomechanical Treatment with Sheet Hydroforming

Investigation of formability, microstructures and post-forming mechanical properties of heat-treatable aluminum alloys subjected to pre-aged hardening warm forming

Investigation of particles on the microstructure, texture and formability of Al–Mg-Si-Zn alloy for automotive body sheet

Modeling mechanical properties and plastic strain for hot forming-quenching AA6061 aluminum alloy parts

Crystal Plasticity Finite Element Analyses on the Formability of AA6061 Aluminum Alloy with Different Ageing Treatments

Research on Alloy Design and Process Optimization of Al–Mg–Zn-Cu-Based Aluminum Alloy Sheets for Automobiles with Secured Formability and Bake-Hardenability

Numerical Analysis of Residual Stresses in Quenched High-Strength Aluminum Alloy Ultra-Thick Plates and their Reduction through Single-Side Cold Compression Method

Investigation of Pre-Aged Hardening Single-Point Incremental Forming Process and Mechanical Properties of AA6061 Aluminum Alloy

Investigation of the Hot Stamping-in-Die Quenching Composite Forming Process of 5083 Aluminum Alloy Skin

Modeling of constitutive behavior and ductile fracture of AA5A06 aluminum alloy sheet in warm hydroforming process