Abstract:Ti6Al4V is the most used alloy for implants because of its excellent biocompatibility; however, its low wear resistance limits its use in the biomedical industry. The additive manufacturing (AM) of Ti6Al4V is a well-established technique that is being used in many fields. However, the AM of Ti6Al4V composites is currently under investigation, and its manufacture using laser powder bed fusion (L-PBF) would result in a great benefit for many industries. The one-step novel concept proposed uses a gas-controlled L-PBF system that enables the AM of layers with different compositions. Six millimeter-edged cubes of Ti6Al4V were manufactured in an Ar atmosphere and coated with in situ Ti6Al4V/TiN layers by using an Ar–N2 mixture given the direct reaction between titanium and nitrogen. Unreinforced Ti6Al4V presented a martensitic microstructure, and TiN reinforcement dendrites and a minor Ti2N phase were gradually introduced into an α + β basketweave titanium matrix. The composites' microhardness, nanohardness, and elastic modulus were 2, 3, and 1.5 times higher, respectively, than those of the Ti6Al4V. Porosity levels (caused by a lack of fusion, trapping gases, and interdendritic porosity), ranged from 7 to 12% (most measured 20–40 μm) and increased with the reinforcement content (15 to 25%). A scaled-up, proof-of-concept design of a hip implant stem was 3D printed using this nitriding method. Since the neck of the stem (top part) is more susceptible to the fracture and fretting corrosion process, the resulting graded material part consisted of unreinforced Ti6Al4V at the bottom and Ti6Al4V/TiN at the top. This change was controlled by gradually adding nitrogen to the atmosphere; moreover, it was found that the more nitrogen in the chamber, the more TiN reinforcement formed in the part. A microhardness of ~450 HV0.1 was measured at the bottom and gradually increased to ~900HV0.1, with the increment corresponding to the in situ TiN reinforcement amount.

TiC/Ti6Al4V functionally graded composite fabricated by in-situ laser additive manufacturing via gas–liquid reaction

Agglomeration-free nanoscale TiC reinforced titanium matrix composites achieved by in-situ laser additive manufacturing

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

In-situ laser additive manufacturing of Ti6Al4V matrix composites by gas–liquid reaction in dilute nitrogen gas atmospheres

Microstructure and Wear Resistance of TiCp/Ti6Al4V Composite Coatings by Follow-Up Ultrasonic-Assisted Laser Additive Manufacturing

Composition design and mechanical properties of B 4 C/Al-Zn-Mg-Cu functionally graded materials prepared by laser additive manufacturing

Microstructure and mechanical properties of TiC-Ni functionally graded materials by simultaneous combustion synthesis and compaction

Microstructure and mechanical properties of in-situ TiC hybrid reinforced TC4 matrix composites by a new additive manufacturing method

Additive Manufacturing of (tib+tic)/ti6al4v Composites with Tailored Network Reinforcement Architecture

New insights into the microstructural evolution and properties of (TiB+TiC)/Ti–6Al–4V composite via laser directed energy deposition using B 4 C nanoparticles

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

Interfacial Microstructures and Mechanical Properties of TiC Reinforced GH 3230 Superalloy Manufactured by Laser Metal Deposition

A One-Step Novel Method to Fabricate Multigrade Ti6Al4V/TiN Composites Using Laser Powder Bed Fusion

A functionally graded material design from stainless steel to Ni-based superalloy by laser metal deposition coupled with thermodynamic prediction

Graded microstructure and properties of TiCp/Ti6Al4V composites manufactured by laser melting deposition

Melting and solidification dynamics during laser melting of reaction-based metal matrix composites uncovered by in-situ synchrotron X-ray diffraction

Microstructure and tensile properties of TiCp/Ti6Al4V composites by laser melting deposition with different dissolving degrees of TiC

Additive manufacturing of a functionally graded material from Ti-6Al-4V to Invar: Experimental characterization and thermodynamic calculations

Microstructure Evolution of TiC Particles In Situ, Synthesized by Laser Cladding

Formability, densification behavior and hierarchical grain structure of laser-directed energy deposition of TiB reinforced titanium matrix composites

Interfacial structures and strengthening mechanisms of in situ synthesized TiC reinforced Ti6Al4V composites by selective laser melting