Abstract:Laser metal deposition (LMD) additive manufacturing process was applied to produce ultrafine TiC particle reinforced Inconel 625 composite parts. The effects of laser energy input per unit length (LEIPUL) on microstructure development, densification response, and mechanical performance including wear performance and tensile properties were comprehensively studied. A relationship of processing conditions, microstructural characteristics, mechanical performance, and underlying strengthening mechanisms was proposed for a successful LMD of high-performance Inconel based composite parts. It revealed that using an insufficient LEIPUL of 33kJ/m lowered the densification behavior of LMD-processed parts, due to the appearance of residual large-sized pores in inter-layer areas of the parts. An increase in LEIPUL above 100kJ/m yielded the near fully dense composite parts after LMD. On increasing LEIPUL, the TiC reinforcing particles became significantly refined and smoothened via the elevated melting of particle surfaces and the dispersion state of ultra-fine reinforcing particles was homogenized due to the efficient action of Marangoni flow within the molten pool. The dendrites of Ni–Cr γ matrix underwent a successive change from an insufficiently developed, disordered microstructure to a refined, ordered microstructure with the increase of LEIPUL. However, the columnar dendrites of the matrix were coarsened apparently at an excessive LEIPUL of 160kJ/m because of the elevated thermalization of the input laser energy. The formation of the refined columnar dendrites of Ni–Cr γ matrix combined with the homogeneously distributed ultra-fine reinforcing particles contributed to the enhancement of wear performance of LMD-processed composites with a considerably low coefficient of friction (COF) of 0.30 and reduced wear rate of 1.3×10−4mm3/Nm. The optimally prepared TiC/Inconel 625 composite parts demonstrated a ductile fracture mode with a sufficiently high tensile strength of 1077.3MPa, yield strength of 659.3MPa, and elongation of 20.7%. The superior tensile properties of LMD-processed parts were attributed to the significant grain refinement effect of the matrix during laser processing and the efficient prohibition of ultrafine reinforcing particles on the mobility of dislocations.

Interfacial Microstructures and Mechanical Properties of TiC Reinforced GH 3230 Superalloy Manufactured by Laser Metal Deposition

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Microstructure and Wear-resistant Properties of in situ TiB-TiC Reinforced Titanium Matrix Composites by Laser Deposition Manufacturing

Microstructure and Tensile Properties of TiCp/Ti6Al4V Titanium Matrix Composites Manufactured by Laser Melting Deposition

Microstructures and Mechanical Properties of Heat Treated TiC/GTD222 Nickel-Based Composite Prepared by Selective Laser Melting

Effect of TiB 2 content on microstructure and mechanical properties of GH3536 superalloy formed by laser solid forming

Microstructure evolution and underlying thermal behavior of high-content TiC reinforced titanium matrix composites fabricated by laser directed energy deposition

Laser Additive Manufacturing of Ultrafine Tic Particle Reinforced Inconel 625 Based Composite Parts: Tailored Microstructures and Enhanced Performance

Formability, densification behavior and hierarchical grain structure of laser-directed energy deposition of TiB reinforced titanium matrix composites

Hot corrosion behavior of a novel TiC/GTD222 nickel-based composite prepared by selective laser melting

Cracking Behaviour and Its Suppression Mechanisms with TiB2 Additions in the Laser Additive Manufacturing of Solid-Solution-strengthened Ni-based Alloys

Interfacial structures and strengthening mechanisms of in situ synthesized TiC reinforced Ti6Al4V composites by selective laser melting

Combined Strengthening of Multi-Phase and Graded Interface in Laser Additive Manufactured Tic/Inconel 718 Composites

Optimization of Processing Parameters and Microstructure Evolution of (TiB+La 2 O 3 )/Ti6Al4V Manufactured by Laser Melting Deposition

Microstructure and Properties of TiC/AlMgSc Composites by Selective Laser Melting

Direct Laser Fabricated in Situ TiC Particulate Reinforced Ni30Al20Fe Intermetallic Matrix Composite

Construction of Three-Dimensional Network Morphology Titanium Matrix Composites Via Adding Nano B4C: As-built and Heat-Treated Scenarios

Effect of laser lower and remelting on the microstructure and tribological properties of GH3230 superalloy coating fabricated by laser melting deposition

Fabrication of a TiC-Ti Matrix Composite Coating Using Ultrasonic Vibration-Assisted Laser Directed Energy Deposition: The Effects of Ultrasonic Vibration and TiC Content

Microstructure and tensile properties of TiCp/Ti6Al4V composites by laser melting deposition with different dissolving degrees of TiC

Nano-size carbide-reinforced Ni matrix composite prepared by selective laser melting