Abstract:Laser metal deposition (LMD) additive manufacturing process was applied to produce ultrafine TiC particle reinforced Inconel 625 composite parts. The effects of laser energy input per unit length (LEIPUL) on microstructure development, densification response, and mechanical performance including wear performance and tensile properties were comprehensively studied. A relationship of processing conditions, microstructural characteristics, mechanical performance, and underlying strengthening mechanisms was proposed for a successful LMD of high-performance Inconel based composite parts. It revealed that using an insufficient LEIPUL of 33kJ/m lowered the densification behavior of LMD-processed parts, due to the appearance of residual large-sized pores in inter-layer areas of the parts. An increase in LEIPUL above 100kJ/m yielded the near fully dense composite parts after LMD. On increasing LEIPUL, the TiC reinforcing particles became significantly refined and smoothened via the elevated melting of particle surfaces and the dispersion state of ultra-fine reinforcing particles was homogenized due to the efficient action of Marangoni flow within the molten pool. The dendrites of Ni–Cr γ matrix underwent a successive change from an insufficiently developed, disordered microstructure to a refined, ordered microstructure with the increase of LEIPUL. However, the columnar dendrites of the matrix were coarsened apparently at an excessive LEIPUL of 160kJ/m because of the elevated thermalization of the input laser energy. The formation of the refined columnar dendrites of Ni–Cr γ matrix combined with the homogeneously distributed ultra-fine reinforcing particles contributed to the enhancement of wear performance of LMD-processed composites with a considerably low coefficient of friction (COF) of 0.30 and reduced wear rate of 1.3×10−4mm3/Nm. The optimally prepared TiC/Inconel 625 composite parts demonstrated a ductile fracture mode with a sufficiently high tensile strength of 1077.3MPa, yield strength of 659.3MPa, and elongation of 20.7%. The superior tensile properties of LMD-processed parts were attributed to the significant grain refinement effect of the matrix during laser processing and the efficient prohibition of ultrafine reinforcing particles on the mobility of dislocations.

High-temperature Oxidation Performance and Its Mechanism of TiC/Inconel 625 Composites Prepared by Laser Metal Deposition Additive Manufacturing

Laser Additive Manufacturing of Ultrafine Tic Particle Reinforced Inconel 625 Based Composite Parts: Tailored Microstructures and Enhanced Performance

Oxidation behavior of in situ TiCp/Ti6Al4V composite with self-assembled network microstructure fabricated by reaction hot pressing

Laser Metal Deposition of TiC/Inconel 718 Composites with Tailored Interfacial Microstructures

Combined Strengthening of Multi-Phase and Graded Interface in Laser Additive Manufactured Tic/Inconel 718 Composites

Evaluation of microstructure, mechanical properties, and corrosion resistance for Ti-doped inconel 625 alloy produced by laser directed energy deposition

Microstructure and Mechanical Properties of Ti-6al-4v Components Fabricated by Laser Micro Cladding Deposition

Microstructural Stability of IN625 Reinforced by the Addition of TiC Produced by Laser Powder Bed Fusion after Prolonged Thermal Exposure

Interfacial Microstructures and Mechanical Properties of TiC Reinforced GH 3230 Superalloy Manufactured by Laser Metal Deposition

Improvement of mechanical properties through inhibition of oxidation by adding TiC particles in laser aided additive manufacturing of stainless steel 316L

Laser metal deposition for additive manufacturing of AA5024 and nanoparticulate TiC modified AA5024 alloy composites prepared with balling milling process

High-temperature oxidation and wear properties of TiC-reinforced CrMnFeCoNi high entropy alloy composite coatings produced by laser cladding

Effect of scanning speed on the high-temperature oxidation resistance and mechanical properties of Inconel 625 alloys fabricated by selective laser melting

Hot corrosion behavior of a novel TiC/GTD222 nickel-based composite prepared by selective laser melting

Tribological and oxidation behaviors of TiN reinforced Co matrix composite coatings on Inconel718 alloy by laser cladding

Fabrication of Nano-Ticp Reinforced Inconel 625 Composite Coatings by Partial Dissolution of Micro-Ticp Through Laser Cladding Energy Input Control

High-temperature oxidation behaviour of Ti65 titanium alloy fabricated by laser direct energy deposition

Effect of Co/TiAl on Mechanical Properties of Laser Melted IN 625 on 304SS Matrix

High temperature oxidation behavior of laser powder bed fusion printed WC/Inconel 718 composites

Microstructure evolution and underlying thermal behavior of high-content TiC reinforced titanium matrix composites fabricated by laser directed energy deposition

Tailored microstructure and enhanced high temperature behavior of TiC/Inconel 718 composites through dual-gradient printing strategy in direct energy deposition