Abstract:The ultra-low dielectric constant (ULK) materials is implemented in the copper/low-k interconnection structures in industry in order to minimize the RC delay and crosstalk noise. The mechanical property of ULK dielectrics is weak compared to traditional dielectrics. So it poses a significant risk to the device reliability, not only in the fabrication process, but also in packaging processes and reliability tests. When using numerical simulations to assess the structural integrity associated with low-k integration, accurate mechanical property of ULK materials is also an important parameter that needed to be measured. In this paper, we present a method of measuring the mechanical properties of ULK materials. This method is suitable for a variety of materials which can be deposited or grown on a silicon substrate. The fabricating processes mainly include lithography, temporary bonding, grinding, Si etching and debonding. In addition, we designed two kinds of test structures. One is with pre-crack, and the other is without pre-crack. Each structure has two kinds of geometry sizes. The tensile test was done by using the in-situ tensiometer apparatus with uniaxial stretching. The stress-strain diagrams of the specimens show an elastic modulus $\mathbf{E=1.2}$ GPa and tensile strength is about 13.5 Mpa for the structure without pre-crack, which is lower than that of bulk low-k material. The samples with two kinds of geometry sizes have similar modulus values which can be converted by the measured results from the diagram. While other specimens show a critical energy release rate ${\mathrm{G}_{\mathrm{c}}=0.25\mathrm{J}/\mathrm{m}^{2}}$ for the structure with pre-crack, which is also lower than that of bulk material. The results illustrate that the ability to resist fracture of low-k thin films is weak. It provides a possible method to measure the mechanical properties of ULK thin films.

Evaluation of a New Advanced Low-k Material

Preparation Of Low-K Nanoporous Sio2 Films By Plasma-Enhanced Chemical Vapor Deposition

20-P-11 Pure-silica Zeolite Low-K Dielectric Thin Films by Spin-on Process

High-Performance Intrinsic Low-K Polymer Via the Synergistic Effect of Its Three Units: Adamantyl, Perfluorocyclobutylidene and Benzocyclobutene

Pure Silica Zeolite Films as Low-k Dielectrics by Spin-On of Nanoparticle Suspensions

Fabrication of the Low-K Films with Tunable K Value As Spacers in Advanced CMOS Technology

Preparation and Characterization of Ultralow-Dielectric-Constant Porous SiCOH Thin Films Using 1,2-Bis(triethoxysilyl)ethane, Triethoxymethylsilane, and a Copolymer Template

Thermally conductive ultra-low-k dielectric layers based on two-dimensional covalent organic frameworks

Characterization of ultra-low k porous organosilica thin films

Characterization of PECVD ultralow dielectric constant porous SiOCH films using triethoxymethylsilane precursor and cinene porogen

Research on the properties of low-k films grafted on Cu (111) surface via electrochemical reduction of aryl diazonium salts

An ultralow-k dielectric derived from a fluorinated polybenzoxazole composite film with yolk–multishell mesoporous silica nanostructures

Low dielectric constant films deposited by PECVD using tetraethoxysilane and limonene as precursors

Tween-80 based ultra low-k (ULK) mesoporous films

Mechanical Properties and Interface Characteristics of Nanoporous Low-K Materials.

Study on the mechanical properties of ultra-low dielectric film by tensile test

Adhesion study of low-k/Si system using 4-point bending and nanoscratch test

A tensile test for freestanding low-k thin films using a lift-off technique

High Dielectric Transparent Film Tailored by Acceptor and Donor Codoping (Small 50/2022)

Thermal Stability of Ultralow k Carbon-Bridged Periodic Mesoporous Organosilica Film

Progress in low dielectric polyimide film – A review