Abstract:Poly(L‐lactide) (PLLA), poly(D‐lactide) (PDLA) and poly(methyl methacrylate) (PMMA) are melt blending with various content of PDLA (0 and 3 wt%) and PMMA (0–20 wt%). The blending pellets then undergoes the melt spinning and hot drawing process to prepare PLA composite fibers. The hydrolysis resistance of fibers is improved by the addition of PMMA and the mechanical property and heat resistance properties increased for the highly oriented crystalline morphology induced by the stereocomplex crystals (SC), which have formed in PLLA/PDLA/PMMA fibers. The SC nanofibrils are detected from the surface morphology of PLLA/PDLA/PMMA fibers after hydrolysis at 60°C for 132 h in NaOH solution. Polylactic acid/poly(methyl methacrylate) (PLA/PMMA) composite fibers with high performance were fabricated using melt spinning technique. The crystallization, lamellae orientation and physical properties of composite fibers were investigated systematically. The addition of PMMA (0–20 wt%) has improved the hydrolysis resistance of composite fibers by preventing water molecules from penetrating and diffusing through the fibers, but the strength and heat resistance were reduced at the same time. The stereocomplex crystallites (SC) formed before spinning by introducing poly(D‐lactide) (PDLA) (3 wt%) in poly(L‐lactide) (PLLA) matrix and acted as nucleating agents to enhanced the crystallization and lamellae orientation of PLLA matrix, which improved the physical properties of PLA composite fibers resultful. The tensile strength of PLA fibers with 3 wt% PDLA and 5 wt% PMMA was increased 31% as well as the boiling water shrinkage and the hydrolysis rate were decreased 30% and 33% in relation to PLLA fibers. Finally, the hydrolysis resistance was further enhanced on the basis of realizing high strength and heat resistance, which is of great significance for preparing durable PLA fiber materials and expanding their application.

Study on properties of polylactic acid/lemongrass fiber biocomposites prepared by fused deposition modeling

Crystallization behavior and mechanical properties of bio-based green composites based on poly(L-lactide) and kenaf fiber

Effect of MAH-g-PLA on the Properties of Wood Fiber/Polylactic Acid Composites

The Effect of a Small Amount of Modified Microfibrillated Cellulose and Ethylene–glycidyl Methacrylate Copolymer on the Crystallization Behaviors and Mechanical Properties of Polylactic Acid

Study on the Compatible Interface of Bamboo Fiber/polylactic Acid Composites by In-Situ Solid Phase Grafting

Preparation of cellulose-graft-polylactic acid via melt copolycondensation for use in polylactic acid based composites: synthesis, characterization and properties

Biocomposites of Polylactic Acid Reinforced by DL-Lactic Acid-Grafted Microfibrillated Cellulose

Investigation into hydroxypropyl-methylcellulose-reinforced polylactide composites for fused deposition modelling

Preparation Of High Performance Biobased Composites From Poly(Lactic Acid) And Microcrystalline Cellulose

Toward durable polylactic acid/poly(methyl methacrylate) polyblend fibers with high performance

Influence of carboxy-terminated hyperbranched polyester and polyethylene glycol on the mechanical and thermal properties of polylactic acid/straw flour composites

Preparation and Characterization of Three-Element Compound Plasticizing Bamboo Fiber-g-Polylactic Acid/Polylactic Acid Composite

Blending and functionalisation modification of 3D printed polylactic acid for fused deposition modeling

Poly(l-lactide)/poly(d-lactide)/bamboo fiber (BF) bio-composites with enhanced heat resistance, mechanical and rheological performance

Preparation Of Plasticized Poly (Lactic Acid) And Its Influence On The Properties Of Composite Materials

Bio-based Green Composites with High Performance from Poly(lactic Acid) and Surface-Modified Microcrystalline Cellulose

Atomic-scale and Experimental Investigation on the Micro-Structures and Mechanical Properties of PLA Blending with CMC for Additive Manufacturing

Preparation and Performance of Poly(lactic Acid)-Wood Flour-Glycidyl Methacrylate-g-Ethylene-Octene Copolymer Composites

Mechanical and thermal properties of bamboo fiber reinforced polypropylene/polylactic acid composites for 3D printing

FDM 3D Printing and Properties of WF/PBAT/PLA Composites

Preparation and Properties of Straw Fiber/Polylactic Acid Composites