Abstract:LiNixCoyMn1–x–yO2 (x ≥ 0.5) layered oxide materials are generally considered as one of the most prospective candidates for lithium-ion battery (LIBs) cathodes due to their high specific capacity and working voltage. However, surface impurity species substantially degrade the electrochemical performance of LIBs. Herein, surface reconstruction from layered structure to disordered layer and rock-salt coherent region together with a uniform Li2CO3-dominant coating layer is first in situ constructed on the single-crystal LiNi0.5Co0.2Mn0.3O2 (NCM) material by a simple water treatment procedure. The unique surface structure is elucidated by Ar-sputtering-assisted X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (spherical aberration-corrected-scanning transmission electron microscopy (STEM), high-resolution transmission electron microscopy (HRTEM), and TEM). Meanwhile, neutron powder diffraction (NPD) indicates that the antisite defect concentration is mitigated in the treated materials. The modified samples display superior cycle stability with a capacity retention of up to 87.5% at 1C after 300 cycles, a high rate capacity of 151 mAh g–1 at 5C, an elevated temperature (45 °C) cycling property with 80% capacity retention (4.5 V), and improved full-cell performance with 91% after 250 cycles at 1C. Importantly, postmortem examination on the cycled cathodes by time-of-flight secondary-ion mass spectroscopy (TOF-SIMS), XPS, TEM, and X-ray diffractometer (XRD) pattern further demonstrate that these results are mainly attributed to the thin cathode electrolyte interface (CEI) film and low solubility of transition-metal ions. Therefore, this expedition provides an opportunity to construct an effective armor for the interface compatibility and stability of LIBs.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c21973?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c21973</a>.XRD patterns and SEM images of NCM, NCM-350 °C, NCM-400 °C, and NCM-500 °C; HRTEM and STEM image of NCM; TEM images of NCM and NCM-400 °C cathode; EDS elemental mapping of the NCM cathode particle; XPS spectra of C 1s, O 1s, and Ni 2p for NCM and NCM-400 °C with different sputtering times (0, 5, 10, 20, 30, 60, 120, 180, 240 s); XPS spectra of Li 1s for NCM and NCM-400 °C surface; cycling performance of graphite at 0.5C at 25 °C within a voltage range of 0.01–3.0 V in a half cell against lithium anodes. Digital images of lithium harvested from the disassembled cycled cells after 500 cycles at 5C for NCM and NCM-400 °C. STEM-EDX, XPS spectra in an argon atmosphere, and SEM image of cycled NCM and NCM-400 °C (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c21973/suppl_file/am0c21973_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Detection of a Cobalt-Containing Interphase at the Li 6 PS 5 Cl-NMC111 Interface by In Situ μXANES and EIS

Surface Analysis of the Lithium-Rich Cathode Material Li<sub>1.2</sub>Mn<sub>0.54</sub>Co<sub>0.13</sub>Ni<sub>0.13</sub>Na<sub><i>x</i></sub>O<sub>2</sub> by Advanced Electron Microscopy

Investigation of Solid Electrolyte Interface Formation in Li3as Electrode Material in a Solid-State Battery Configuration

Spatio-chemical deconvolution of the LiNi0.6Co0.2Mn0.2O2/Li6PS5Cl interphase layer in all-solid-state batteries using combined X-ray spectroscopic methods

In Situ Induced Surface Reconstruction of Single-Crystal Lithium-Ion Cathode Toward Effective Interface Compatibility

Unraveling the Intra and Intercycle Interfacial Evolution of Li6PS5Cl‐Based All‐Solid‐State Lithium Batteries

Investigation of Interfacial Behavior of Ni-Rich NCM Cathode Particles in Sulfide-Based Solid-State Electrolyte

Stabilized Cathode/Sulfide Electrolyte Interface through Conformally Interfacial Nanocoating for All-Solid-State Batteries

Unraveling the Intra and Intercycle Interfacial Evolution of Li <sub>6</sub> PS <sub>5</sub> Cl‐Based All‐Solid‐State Lithium Batteries

Surface Analysis of the Lithium-Rich Cathode Material Li1.2Mn0.54Co0.13Ni0.13NaxO2 by Advanced Electron Microscopy

Slurry-Coated LiNi0.8Co0.1Mn0.1O2-Li3InCl6 Composite Cathode with Enhanced Interfacial Stability for Sulfide-Based All-Solid-State Batteries.

Enabling superior electrochemical performance of NCA cathode in Li5.5PS4.5Cl1.5-based solid-state batteries with a dual-electrolyte layer

Integrated Interface Configuration by In-Situ Interface Chemistry Enabling Uniform Lithium Deposition in All-Solid-state Lithium Metal Batteries

High Lithium-Ion Conductivity, Halide-Coated, Ni-Rich NCM Improves Cycling Stability in Sulfide All-Solid-State Batteries

Quantification of the Li-ion Diffusion over an Interface Coating in All-Solid-state Batteries Via NMR Measurements

Elucidating and Minimizing the Space‐Charge Layer Effect between NCM Cathode and Li6PS5Cl for Sulfide‐Based Solid‐State Lithium Batteries

Probing Depth-Dependent Transition-Metal Redox of Lithium Nickel, Manganese, and Cobalt Oxides in Li-Ion Batteries

Dual modified NCMA cathode with enhanced interface stability enabled high-performance sulfide-based all-solid-state lithium battery

Chemo-mechanical stable cathode interphase via interface in-situ catalytic-conversion integrated design for all solid-state batteries

Interphase Stabilization of LiNi0.5 Mn1.5 O4 Cathode for 5 V-Class All-Solid-State Batteries

Manipulating interfacial stability of LiNi0.5Co0.3Mn0.2O2 cathode with sulfide electrolyte by nanosized LLTO coating to achieve high-performance all-solid-state lithium batterie