Abstract:Lithium-ion batteries (LIBs) become an essential part of many portable devices and even electric vehicles than ever before. Among the various cathode materials, Ni rich layered cathode material has big attention because it has higher specific capacity and energy density. However, at a delithiated state, unstable Ni 4+ leads to oxygen release and structural degradation and as a result, irreversible phase transition from R3m to electrochemical inactive Fm3m is observed. So, various strategy is applying to overcome this limitation like three-component system (NCM) or surface coating. However, NCM still cannot solve that problem perfectly and surface coating makes a problem like reducing specific capacity caused by insulating coating material (Al 2 O 3 , MnO 2 ...etc) And also, this day, Co free structure of Ni rich cathode material has received more great attention as an alternative to NCM because of its hazardous toxicity and increasing price of Co. At this perspective, many studies have demonstrated Core-Shell or FCG (Full Concentration Gradient) structure can make better structural stability without Co metal than surface coating, which has insulated coating materials. In addition, core shell structure is easier to control the composition than FCG structure. However, in Core-Shell structure, interdiffusion of shell metal to core deteriorate the stability of Core-Shell material, so it needs very delicate heat treatment. And generally, to prevent interdiffusion from traditional core-shell structure, lower synthesis temperature or high valence metal dopant would be needed and that leads lower initial specific capacity or additional doped metal. So, we prevent the Mn interdiffusion by changing valence state of Mn in precursor through simple convection drying process not vacuum drying without decreasing synthesis temperature and additional dopant. Atomic interdiffusion in layered metal oxide structures follows the atomic migration through octahedral and tetrahedral sites. In case of various stated Mn, higher valence state Mn has higher energy barrier to migrate between each Oh and Td sites. Based on this theory, surface Mn rich shell can be oxidized easily under convection oven drying and highly oxidized Mn will be remained better than lower state Mn during high temperature calcination. These more remained Mn in shell can protect the particle surface from electrolyte attack and also higher valence state Mn makes slightly more Ni 2+ due to thermodynamic stability and charge balance of Mn on the surface. And that Ni 2+ in Li slab (Cation mixing) acts as a pillar to suppress irreversible phase transition of Ni rich materials. Through this surface passivation, phase transition (layered to rock salt ) propagation surface to bulk can be blocked. Furthermore, mechanical pulverization of secondary particle is also prevented because of less permeating electrolyte into bulk structure. Therefore, Li ion diffusion will not be sluggish after cycling as observed by GITT. In addition, more clear Ni rich core assure high specific capacity and faster electrochemical reaction kinetic without severe capacity fading. And also, in Full cell test (using graphite as anode), convection oven dried sample has better structure stability and that means our strategy for core-shell LiNi 0.97 Mn 0.03 O 2 sample can be good candidate to alternate conventional cathode active material for Lithium ion battery practically. As prepared materials, atomic distribution was observed by EDS and XPS analysis. This study suggests useless of vacuum drying and more cost effective way to prepare Co free Core Shell LiNi 0.97 Mn 0.03 O 2 cathode material for Lithium Ion Batteries.

Surface Analysis of the Lithium-Rich Cathode Material Li1.2Mn0.54Co0.13Ni0.13NaxO2 by Advanced Electron Microscopy

Surface Analysis of the Lithium-Rich Cathode Material Li<sub>1.2</sub>Mn<sub>0.54</sub>Co<sub>0.13</sub>Ni<sub>0.13</sub>Na<sub><i>x</i></sub>O<sub>2</sub> by Advanced Electron Microscopy

Monitoring the Formation of Nickel-Poor and Nickel-Rich Oxide Cathode Materials for Lithium-Ion Batteries with Synchrotron Radiation

Cathode Materials of Li_xCo_(0.8)Ni_(0.2)O_2 for Lithium-ion Battery

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Electron Microscopy Study of Surface Reconstruction and Its Evolution in P2-Type Na0.66mn0.675ni0.1625co0.1625o2 for Sodium-Ion Batteries

Probing the Thermal-Driven Structural and Chemical Degradation of Ni-Rich Layered Cathodes by Co/Mn Exchange

Atomic scale evolution of the surface chemistry in Li[Ni,Mn,Co]O2 cathode for Li-ion batteries stored in air

Monitoring LiNi x Co y Mn (1-x-y) O 2 Degradation in Contact with Li via In Situ Transmission Electron Microscopy

Chemical-Mechanical Effects in Ni-Rich Cathode Materials

Insight into the Structural Evolution and Thermal Behavior of LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode under Deep Charge

Electrochemical Characteristics of Layered Transition Metal Oxide Cathode Materials for Lithium Ion Batteries: Surface, Bulk Behavior, and Thermal Properties

Ab Initio Study on Surface Segregation and Anisotropy of Ni-Rich LiNi1–2yCoyMnyO2 (NCM) (y ≤ 0.1) Cathodes

Synthesis and Mechanism of High Structural Stability of Nickel-Rich Cathode Materials by Adjusting Li-Excess

In Situ Induced Surface Reconstruction of Single-Crystal Lithium-Ion Cathode Toward Effective Interface Compatibility

Origin of oxygen-redox and transition metals dissolution in Ni-rich LixNi0.8Co0.1Mn0.1O2 cathode

Mn Interdiffusion Mobility Controlled By Simple Drying Process for Cobalt Free Core-Shell Ni Rich Cathode Material in Lithium Ion Batteries

Surface reconstruction and chemical evolution of stoichiometric layered cathode materials for lithium-ion batteries

Direct Observation Of Defect-Aided Structural Evolution In A Nickel-Rich Layered Cathode

The Role of Cobalt and Manganese for the Safety of Ni-Rich NMC Cathode

Surface Surgery of the Nickel-Rich Cathode Material LiNi0.815Co0.15Al0.035O2: Toward a Complete and Ordered Surface Layered Structure and Better Electrochemical Properties