Abstract:Single-walled carbon nanotubes (SWNTs) with outstanding electronic, optical, mechanical, and thermal properties are expected to be the most promising materials for next-generation energy devices as well as optical and electronic devices. However, the structure controlled assembly of SWNTs for various devices is still challenging. In this study, we discuss two different SWNT assemblies for SWNT-Si heterojuction solar cells. We proposed a water vapor treatment to build up SWNTs to a self-assembled micro-honeycomb network for the application of solar cells [1]. The micro-honeycomb network consists of vertical aggregated SWNT walls and a buckypaper bottom (quasi 2 dimentional random network). This hierarchical structure exhibits lower sheet resistance and higher optical transmittance compared with the buckypaper. The heterojunction solar cell was fabricated by dry depositing the SWNT film to the 3 mm by 3 mm n-type silicon substrate. The pristine SWNT-Si heterojunction solar cell shows a record-high fill factor of 72 % as well as a power conversion efficiency (PCE) of 6 % without tuning the diameter or height of original vertically aligned SWNTs [2]. The PCE remains stable for months in ambient condition. A PCE exceeding 10 % is achieved in the dry state after dilute nitric acid treatment. On the other hand, heterojucntion solar cells using highly transparent-conductive SWNT films from controlled bundle-diameter and long bundle length [3] are also promising. Here, SWNTs were synthesized by the thermal decomposition of ferrocene vapor in a carbon monoxide atmosphere, with the average diameter of approx. 2 nm. The SWNT films showed a sheet resistance of 117 Ω/sq. at the transmittance of 91 % over the AM1.5G spectrum. Our preliminary test result shows the PCE of 10.12 %, with short-circuit current, open-circuit voltage and fill factor of 30.9 mA/cm 2 , 540 mV and 60 %, respectively. Both types of solar cells are stable after months, which is attributed to the high-purity pristine SWNTs. The updated performance of these solar cells and the detailed mechanism will be discussed. References: [1] K. Cui, T. Chiba, S. Omiya, T. Thurakitseree, P. Zhao, S. Fujii, H. Kataura, E. Einarsson, S. Chiashi, S. Maruyama, J. Phys. Chem. Lett., (2013), 4, 2571. [2] Y. Murakami, S. Chiashi, Y. Miyauchi, M. Hu, M. Ogura, T. Okubo, S. Maruyama, Chem. Phys. Lett., (2004), 385, 298. [3] A. G. Nasibulin, A. Kaskela, K. Mustonen, A. S. Anisimov, V. Ruiz, S. Kivistö, S. Rackauskas, M. Y. Timmermans, M. Pudas, B. Aitchison, M. Kauppinen, D. P. Brown, O. G. Okhotnikov, E. I. Kauppinen, ACS Nano, (2011), 5, 3214.

Commercial carbon nanotube as rear contacts for industrial p-type silicon solar cells with an efficiency exceeding 23%

Incorporating Semiconducting Single-Walled Carbon Nanotubes As Efficient Charge Extractors in Organic Solar Cells

Heterojunction Photovoltaic Devices Utilizing Single Wall Carbon Nanotube Thin Films and Silicon Substrates

High-performance bifacial perovskite solar cells enabled by single-walled carbon nanotubes

Carbon-Nanotube Solar Photovoltaic Microcells with Nanowelded Contacts

Enriched Semiconducting Single Wall Nanotubes As Back Contact for CdTe Solar Cell.

Air-Stable High-Efficiency Solar Cells with Dry-Transferred Single-Walled Carbon Nanotube Films

Stable Organic Passivated Carbon Nanotube–Silicon Solar Cells with an Efficiency of 22%

Contact-dominated Transport in Carbon Nanotube Thin Films: Toward Large-Scale Fabrication of High Performance Photovoltaic Devices.

An industrially viable TOPCon structure with both ultra-thin SiOx and n+-poly-Si processed by PECVD for p-type c-Si solar cells

A Polymer/Carbon‐Nanotube Ink as a Boron‐Dopant/Inorganic‐Passivation Free Carrier Selective Contact for Silicon Solar Cells with over 21% Efficiency

21.3%-Efficient N-Type Silicon Solar Cell with a Full Area Rear TiOx/LiF/Al Electron-Selective Contact

High‐Performance ITO‐Free Perovskite Solar Cells Enabled by Single‐Walled Carbon Nanotube Films

High-efficiency N-Type Silicon PERT Bifacial Solar Cells with Selective Emitters and Poly-Si Based Passivating Contacts

Comparison of Nanocarbon-Silicon Solar Cells with Nanotube-Si or Graphene-Si Contact

Approaching 23% with large‐area monoPoly cells using screen‐printed and fired rear passivating contacts fabricated by inline PECVD

Interface Passivation Treatment Enables GaAs/CNT Heterojunction Solar Cells over 19% Efficiency

Improved Photovoltaic Performance of GaAs/Carbon Nanotube Heterojunction Solar Cells with a Multifunctional Nafion/PEDOT:PSS Layer

(Invited) Carbon Nanotube Network As Stable and Efficient Electron Blocking Layer and Transparent Conductive Electrodes for Solar Cells

Stable Dopant-Free Electron-Selective Contact for Silicon Solar Cells

Improved CNT-Si Heterojunction Solar Cell with Structured Single-Walled Carbon Nanotubes