Abstract:Magnetorheological elastomers (MRE) are intelligent controllable materials used as polishing pads in chemical mechanical polishing (CMP), and the magnetic particles in the MRE polishing pad are used as solid-phase catalysts for heterogeneous Fenton reactions for oxidizing single-crystal SiC surfaces, thereby helping reduce the processing difficulty and obtain high-quality surfaces. The influence of the solid-phase catalyst (Fe3O4 mass fraction, particle size) and polishing solution environment (H2O2 concentration, pH value) on the CMP heterogeneous Fenton reaction polishing single-crystal SiC were investigated. The material removal behavior of the MRE polishing pad was investigated. The results demonstrated that the solid-phase catalyst, Fe3O4, has a better superior effect than the carbonyl iron powder (CIP). The polishing material removal rate (MRR) increased and the surface roughness (Ra) decreased with an increase in the Fe3O4 mass fraction. Superior polishing results were obtained at a particle size of 0.3 μm. The higher the H2O2 concentration in the polishing solution, the greater the MRR, with lower Ra at 10% concentration. The highest MRR and lowest Ra were achieved at pH = 3 in acidic environments. During polishing, the heterogeneous Fenton reaction can significantly enhance the removal ability of polishing materials. The MRR increased by 33.4% with the heterogeneous Fenton reaction compared with those without the heterogeneous Fenton reaction, and the contribution of the heterogeneous Fenton reaction to total material removal was 25.03%. The analysis of the SiC–Abrasive–MRE polishing pad contact state revealed that the heterogeneous Fenton reaction can oxidize the SiC surface and reduce the surface hardness, increasing the indentation depth δwa of the abrasive grain into the SiC surface and exhibiting greater material removal.

Material removal rate model for chemical–mechanical polishing of single-crystal SiC substrates using agglomerated diamond abrasive

Novel model of material removal rate on ultrasonic-assisted chemical mechanical polishing for sapphire

Material Removal Mechanism in Chemical Mechanical Polishing: Theory and Modeling

Modeling of Material Removal Rate for the Fixed-Abrasive Double-Sided Planetary Grinding of a Sapphire Substrate

Tribochemical mechanisms of abrasives for SiC and sapphire substrates in nanoscale polishing

Investigation on Material Removal Mechanisms in Photocatalysis-Assisted Chemical Mechanical Polishing of 4H–SiC Wafers

Polishing Mechanism of CMP 4H-SiC Crystal Substrate (0001) Si Surface Based on an Alumina (Al2O3) Abrasive

Material Removal Regions in Chemical Mechanical Polishing: Coupling Effects of Slurry Chemicals, Abrasive Size Distribution and Wafer-Pad Contact Area, Part 1

Wear mechanism in nano polishing of SiCp/Al composite materials using molecular dynamics

A plasticity-based model of material removal in chemical-mechanical polishing (CMP)

Optimization of polishing fluid composition for single crystal silicon carbide by ultrasonic assisted chemical-mechanical polishing

Material Removal Regions in Chemical Mechanical Planarization for Submicron Integrated Circuit Fabrication: Coupling Effects of Slurry Chemicals, Abrasive Size Distribution,and Wafer-Pad Contact Area

Surface Morphology Evolution during Chemical Mechanical Polishing Based on Microscale Material Removal Modeling for Monocrystalline Silicon

Study on heterogeneous Fenton reaction parameters for polishing single-crystal SiC using magnetorheological elastomers polishing pads

A Coupled Material Removal Model for Chemical Mechanical Polishing Processes

Investigation of the chemical action mechanism based on reactive force field in SiC chemical–mechanical polishing process

Mechanical removal of SiC by multi-abrasive particles in fixed abrasive polishing using molecular dynamics simulation

Surface modulation to enhance chemical mechanical polishing performance of sliced silicon carbide Si-face

Mechanical Model of Single Abrasive During Chemical Mechanical Polishing: Molecular Dynamics Simulation

Mechanistic difference between Si-face and C-face polishing of 4H–SiC substrates in aqueous and non-aqueous slurries

Non-continuum Material Removal Mechanism of Surface Polishing with Ultra Precision