Abstract:3D printing utilized as a direct deposition of conductive polymeric materials onto textiles reveals to be an attractive technique in the development of functional textiles. However, the conductive fillers—filled thermoplastic polymers commonly used in the development of functional textiles through 3D printing technology and most specifically through Fused Deposition Modeling (FDM) process—are not appropriate for textile applications as they are excessively brittle and fragile at room temperature. Indeed, a large amount of fillers is incorporated into the polymers to attain the percolation threshold increasing their viscosity and stiffness. For this reason, this study focuses on enhancing the flexibility, stress and strain at rupture and electrical conductivity of 3D-printed conductive polymer onto textiles by developing various immiscible polymer blends. A phase is composed of a conductive polymer composite (CPC) made of a carbon nanotubes (CNT) and highly structured carbon black (KB)- filled low-density polyethylene (LDPE) and another one of propylene-based elastomer (PBE) blends. Two requirements are essential to create flexible and highly conductive monofilaments for 3D-printed polymers onto textile materials applications. First, the co-continuity of both the thermoplastic and the elastomer phases and the location of the conductive fillers in the thermoplastic phase or at the interface of the two immiscible polymers are necessary to preserve the flexibility of the elastomer while decreasing the global amount of charges in the blends. In the present work based on theoretical models, when using a two-step melt process, the KB and CNT particles are found to be both preferentially located at the LDPE/PBE interface. Moreover, in the case of the two-step extrusion, SEM characterization showed that the KB particles were located in the LDPE while the CNT were mainly at the LDPE/PBE interface and TEM analysis demonstrated that KB and CNT nanoparticles were in LDPE and at the interface. For one-step extrusion, it was found that both KB and CNT are in the PBE and LDPE phases. These selective locations play a key role in extending the co-continuity of the LDPE and PBE phases over a much larger composition range. Therefore, the melt flow index and the electrical conductivity of monofilament, the deformation under compression, the strain and stress and the electrical conductivity of the 3D-printed conducting polymer composite onto textiles were significantly improved with KB and CNT-filled LDPE/PBE blends compared to KB and CNT-filled LDPE separately. The two-step extrusion processed 60%(LDPE16.7% KB + 4.2% CNT)/40 PBE blends presented the best properties and almost similar to the ones of the textile materials and henceforth, could be a better material for functional textile development through 3D printing onto textiles.

Interface and Friction Properties of Copper-embedded Polyethylene Terephthalate Filament

Study on Silk Fibroin Coated PET Fabric

Fully bio-based flame retardant and antibacterial coating for polyethylene terephthalate fabric

The Electrical and Mechanical Behaviors of Copper Thin Films Deposited on Polyethylene Terephthalate Under Tensile Stress

Effect of the angle of the laid-up filaments on the surfaces on the coefficient of static friction between parts manufactured by extrusion-based 3D printing

Preparation of a copper porphyrin derivative and its surface modification for simultaneously endowing PET fibers with dyeing, flame retardant and anti-dripping performance

Reuse polyester/cotton blend fabrics to prepare fiber reinforced composite: Fabrication, characterization, and interfacial properties evaluation

Development of an Elastic, Electrically Conductive Coating for TPU Filaments

Microstructure of Carbon Nanotubes/pet Conductive Composites Fibers and Their Properties

Characterization and Application to Fiber Reinforced Composite of Catechol/polyethyleneimine Modified Polyester Fabrics by Mussel-inspiration

Mechanical and Tribological Properties of PA66/PPS Blend. II. Filled with PTFE

STUDY OF THE INFLUENCE OF COPPER REINFORCEMENT ON THE TRIBOLOGICAL PROPERTIES OF PARTS OBTAINED BY FUSED FILAMENT FABRICATION

A Study on the Mechanical and Tribological Properties of Carbon Fabric/PTFE Composites

Fabrication of selective electroless copper plating on PET sheet: Effect of PET surface structure on resolution and adhesion of copper coating

Study on tribological properties of frictional material based aromatic polyamide

Development of a TPU/CNT/Cu Composite Conductive Filament with a High CNT Concentration

Synergistic effect on the mechanical, thermal, and tribology characteristics of modified natural fibre composites with perforated waste PET

Fabrication, Structural Characterization, Dielectric Analysis and Thermal Properties of Novel Flexible Polymer Composite Films

Development of Flexible and Conductive Immiscible Thermoplastic/Elastomer Monofilament for Smart Textiles Applications Using 3D Printing

Performance Evaluation of CNT Reinforcement on Electroless Plating on Solid Free-Form-Fabricated PETG Specimens for Prosthetic Limb Application

PET Surface Modification with Inkjet-Printing Pd 2+ /Epoxy Resin Solution for Selective Electroless Copper Plating