Abstract:Hybrid calcium carbonate particles, synthesized III the presence of block copolymer polystyrene-b-poly(acrylic acid) (PS-b-PAA), were used to fabricate polyelectrolyte (PE) such as polylallyamine hydrochloride)/ poly(strene sulfonate sodium) (PAH/PSS) and poly (diallyldimethyl ammonium chloride)/poly (styrene sulforate sodium) (PADH/PSS) Capsules, by layer-by-layer (LbL) technique. Novel micelle-enhanced polyelectrolyte (PE capsules were thus obtained. The structure of the micelle-enhanced PE microcapsules was studied in this article. Due to the presence of a large amount of negatively charged micelles inside PE capsule interior, which were liberated from templates, the capsule wall was tightly re-constructed. Different from the wall properties of the conventional PE capsules, the wall of the micelle-enhanced PE capsules showed stability under an extensive pH range from I to 14, but the micelled enhanced capsules showed dented morphology in solutions with high NaCl concentration such as 0.5 mol/L and I mol/L. The state of the block copolymer in the capsules was investigated in dialysis bag by simulating the Solution condition of the capsule interior after the template being removed. It was found that the micelle size of the block copolymer In solution of templates dissolution was tens of nanometers after the solution was dialyzed for 24 h. With the dialysis time increasing up to at least 72 It, the block copolymer began to precipitate onto the dialysis bag from the solution The interaction between the 2-D polyelectrolyte multilayer film and micelles formed by block copolymer in templates solution was studied by UV-Vis measurements as well. It was found that PE multilayer could interact with micelles via electrostatic force. At the same time I the block copolymer remained in the capsules interior could be precipitated onto the PE multilayer via dialyzing in deionized water for a long time (pH similar to 6). A micelle-related layer was formed which was stabilized by the "bridge effect" of calcium ions. That is, the wall of the micelle-enhanced PE capsules had a bilayer structure and was formed by the polyelectrolyte multilayer and micelle-related layer. It seemed that the two layers with different properties clung to each other via electrostatic force. The formation mechanism of the bilayer structure was well illuminated oil the aforementioned studies. This is a key property of the micelle-enhanced PE capsules with which all the properties of the capsules were linked. Based on the bilayer structure of the capsules, the morphology changes of the capsules in solutions with different conditions such as high NaCl concentrations could be elucidated well. However, more direct proofs and further studies were needed to completely resolve the fine structure of the micelle-enhanced PE capsules.

Fabrication of Porous Capsules Encapsulating Lithium Adsorbent Using Polyethylene Glycol and Evaluation of Adsorption Performance

Preparation of "micelles enhanced " polyelectrolyte capsules

Preparation Of Pvdf/P(Mma-Co-Pegma) Porous Membranes Via Phase Inversion Process For Gel Polymer Electrolyte

Effects of PDMS with Polyether Side Chains on the Fluoropolymer Based Gel Lithium Electrolytes

A Study of Properties of "Micelle-Enhanced" Polyelectrolyte Capsules: Structure, Encapsulation and in Vitro Release

Porous Carbon Globules with Moss-Like Surfaces from Semi-Biomass Interpenetrating Polymer Network for Efficient Charge Storage

Highly efficient and stable adsorption of lithium from brine with microcapsules containing 1-phenylazo-2-naphthol and trioctylphosphine oxide

Synthesis of Size-Controlled Acid-Resistant Hybrid Calcium Carbonate Microparticles As Templates for Fabricating “Micelles-Enhanced” Polyelectrolyte Capsules by the LBL Technique

Structure Studies of Micelle-Enhanced Polyelectrolyte Microcapsules

Macroporous Lithium Adsorbent Monolith Prepared via High Internal Phase Emulsion Technique

In Situ Coacervated Microcapsules with Filled Polyelectrolytes and Charge‐Controlled Permeation for Dye Molecules

A Facile Pathway to Fabricate Microcapsules by in Situ Polyelectrolyte Coacervation on Poly(styrene Sulfonate)-Doped CaCO3particles

Electrospun Lithium Porous Nanosorbent Fibers for Enhanced Lithium Adsorption and Sustainable Applications

Preparation and Adsorption Performance of Polyvinyl Chloride/Polyacrylonitrile Blended Lithium Ion-Sieve Membrane

Porous polyvinyl alcohol/polyacrylamide hydrogels loaded with HTO lithium-ion sieves for highly rapid and efficient Li + extraction

Lithium-ion adsorption on surface modified porous carbon

3D printed cylindrical capsules as a Chlorella pyrenoidosa immobilization device for removal of lead ions contamination

Charge-Controlled Permeability of Polyelectrolyte Microcapsules

Aggregation-Resistant Superparamagnetic Noncovalent Hybrid Multilayer Hollow Microcapsules in High Ionic Strength Media

Preparation of polyepoxide microcapsule via interfacial polyaddition reaction in W/O and O/W emulsion systems

A lithium ion-imprinted adsorbent using magnetic carbon nanospheres as a support for the selective recovery of lithium ions