Abstract:Introduction: Bone defects remain a thorny challenge that clinicians have to face. At present, scaffolds prepared by 3D printing are increasingly used in the field of bone tissue repair. Polylactic acid (PLA) has good thermoplasticity, processability, biocompatibility, and biodegradability, but the PLA is brittle and has poor osteogenic performance. Beta-tricalcium phosphate (Î2-TCP) has good mechanical properties and osteogenic induction properties, which can make up for the drawbacks of PLA. Methods: In this study, photocurable biodegradable polylactic acid (bio-PLA) was utilized as the raw material to prepare PLA/Î2-TCP slurries with varying Î2-TCP contents (Î2-TCP dosage at 0%, 10%, 20%, 30%, 35% of the PLA dosage, respectively). The PLA/Î2-TCP scaffolds were fabricated using liquid crystal display (LCD) light-curing 3D printing technology. The characterization of the scaffolds was assessed, and the biological activity of the scaffold with the optimal compressive strength was evaluated. The biocompatibility of the scaffold was assessed through CCK-8 assays, hemocompatibility assay and live-dead staining experiments. The osteogenic differentiation capacity of the scaffold on MC3T3-E1 cells was evaluated through alizarin red staining, alkaline phosphatase (ALP) detection, immunofluorescence experiments, and RT-qPCR assays. Results: The prepared scaffold possesses a three-dimensional network structure, and with an increase in the quantity of Î2-TCP, more Î2-TCP particles adhere to the scaffold surface. The compressive strength of PLA/Î2-TCP scaffolds exhibits a trend of initial increase followed by decrease with an increasing amount of Î2-TCP, reaching a maximum value of 52.1Â MPa at a 10% Î2-TCP content. Degradation rate curve results indicate that with the passage of time, the degradation rate of the scaffold gradually increases, and the pH of the scaffold during degradation shows an alkaline tendency. Additionally, Live/dead staining and blood compatibility experiments suggest that the prepared PLA/Î2-TCP scaffold demonstrates excellent biocompatibility. CCK-8 experiments indicate that the PLA/Î2-TCP group promotes cell proliferation, and the prepared PLA/Î2-TCP scaffold exhibits a significant ability to enhance the osteogenic differentiation of MC3T3-E1 cells in vitro . Discussion: 3D printed LCD photocuring PLA/Î2-TCP scaffolds could improve surface bioactivity and lead to better osteogenesis, which may provide a unique strategy for developing bioactive implants in orthopedic applications.

Microstructures and mechanical properties of biphasic calcium phosphate bioceramics fabricated by SLA 3D printing

3D-Printed Bioceramic Scaffolds with High Strength and High Precision

Effect of Foreign Ion Substitution and Micropore Tuning in Robocasting Single-Phase Bioceramic Scaffolds on the Physicochemical Property and Vascularization

Fabrication of cancellous-bone-mimicking β-tricalcium phosphate bioceramic scaffolds with tunable architecture and mechanical strength by stereolithography 3D printing

Digital light processing (DLP) of nano biphasic calcium phosphate bioceramic for making bone tissue engineering scaffolds

3D Printing Bioceramic Porous Scaffolds with Good Mechanical Property and Cell Affinity

3D Printing Magnesium-Doped Wollastonite/β-Tcp Bioceramics Scaffolds with High Strength and Adjustable Degradation

Bone regeneration in 3D printing bioactive ceramic scaffolds with improved tissue/material interface pore architecture in thin-wall bone defect

Preparation and Characterization of 3D Printed Porous 45S5 Bioglass Bioceramic for Bone Tissue Engineering Application

Fabrication and properties of PLA/Î2-TCP scaffolds using liquid crystal display (LCD) photocuring 3D printing for bone tissue engineering

Ultrahigh Strength of Three-Dimensional Printed Diluted Magnesium Doping Wollastonite Porous Scaffolds

DLP 3D printing porous β-tricalcium phosphate scaffold by the use of acrylate/ceramic composite slurry

Microstructures and properties of 45S5 bioglass® & BCP bioceramic scaffolds fabricated by digital light processing

Tuning filament composition and microstructure of 3D-printed bioceramic scaffolds facilitate bone defect regeneration and repair

369Fabrication of 3D gel-printed β-tricalcium phosphate/titanium dioxide porous scaffolds for cancellous bone tissue engineering

Preparation of BMP-2/PDA-BCP Bioceramic Scaffold by DLP 3D Printing and its Ability for Inducing Continuous Bone Formation

Support-less ceramic 3D printing of bioceramic structures using a hydrogel bath

Fabrication of 3D gel-printed β-tricalcium phosphate/titanium dioxide porous scaffolds for cancellous bone tissue engineering

3D printing calcium phosphate ceramics with high osteoinductivity through pore architecture optimization

Fabrication of 3D printed Ca3Mg3(PO4)4-based bioceramic scaffolds with tailorable high mechanical strength and osteostimulation effect

High performance hydroxyapatite ceramics and a triply periodic minimum surface structure fabricated by digital light processing 3D printing