Abstract:In this study, treatment of phosphogypsum (PG) with lime-water (LWT), sulphuric acid (SAT), a mixture of H2SO4 and HNO3 (AWT), PG-water (ST), and PG-limestone (LT) was attempted to purify PG and improve its quality so that it can be used for manufacture of ordinary Portland Cement (OPC). The treatment of PG removes P2O5, SO3, and MgO impurities into water-leachable phase. Chemical analysis of the treated PG and mechanical properties of OPC mortar after various treatment of PG established improvement of the quality of PG. The purified PG contain less impurities when compared with untreated PG. It was observed that the leachable of P2O5, SO3, and MgO in these samples ranged from 86% to 90%, 69% to 94%, 96% to 99%, respectively, can be achieved using these treatment processes. The major phases Alite (C3S), Belite (C2S), Aluminatetricalcic(C3A), and Tetra-calcium aluminoferrite (C4AF), and control ratios Lime Saturation factor (LSF), Aluminum/Iron ratio (AR), and Silica ratio (SR) were measured. These experimental results showed that the C3S, C3A and C4AF, C2S, LSF, AR, and SR contents fulfilled the requirement of the Jordan Standards and European Standards; hence treated PG can be replaced by natural gypsum. The X-ray diffraction analysis of OPC samples showed that C3S and C2S are major mineral phases, C3A and C4AF represent as minor constituents while the CaO and MgO represent as trace phases. The effect of treated PG on the mechanical properties of OPC mortar was investigated. The OPC produced with purified phosphogypsum were found to have strength properties similar to those produced from mineral gypsum thus fulfilling Jordan Standards and European Standards. The present study indicates that the use of PG in OPC manufacture can solve the waste disposal problem thus cleaning our environment at one hand, on the other hand it can save natural raw materials i.e gypsum.Bangladesh J. Sci. Ind. Res. 50(4), 241-250, 2015

PURIFICATION OF PHOSPHOGYPSUM FOR USE AS CEMENT RETARDER BY SULPHURIC ACID TREATMENT

Efficient precipitation of soluble phosphorus impurities in the recycling of phosphogypsum to produce hemihydrate gypsum

Treating waste phosphogypsum for cement and plaster manufacture

Influence of treated waste phosphogypsum materials on the properties of ordinary portland cement

Harmless Treatment of Phosphogypsum in Industrial Application

Gradient removal of Si and P impurities from phosphogypsum and preparation of anhydrous calcium sulfate

Research on the technology and mechanism of direct acidification of phosphogypsum and deeply solidify impurities with lime

Application of lime neutralised phosphogypsum in supersulfated cement

Utilization of solidified phosphogypsum as Portland cement retarder

Deep removal of phosphorus and synchronous preparation of high-strength gypsum from phosphogypsum by crystal modification in NaCl-HCl solutions

Study of Semi-Dry High Target Solidification/Stabilization of Harmful Impurities in Phosphogypsum by Modification

Phosphogypsum as a component of calcium sulfoaluminate cement: Hazardous elements immobilization, radioactivity and performances

Influence of Impurities on the Process of Obtaining Calcium Carbonate during the Processing of Phosphogypsum

Study on Phosphogypsum As a Cement Retarder

Efficient removal of impurities from phosphogypsum during preparation of α-hemihydrate gypsum

Efficient extraction of impurities from phosphogypsum during crystal regulation of α‐hemihydrate gypsum

Modification of phosphogypsum using circulating fluidized bed fly ash and carbide slag for use as cement retarder

Investigating the novel process for thorough removal of eutectic phosphate impurities from phosphogypsum

Preparation of gypsum with high purity and whiteness from phosphogypsum for CO2 mineral sequestration

Effect of Phosphogypsum on the Properties of Portland Cement