Abstract:As a surface-strengthening technology, electro-spark deposition (ESD) is widely used in the strengthening and repair of key components of high-end equipment. In this paper, a fusion and solidification model of ESD coating is established. The method of heat–fluid–solid interaction is adopted to simulate the material’s flow and fusion process in the droplet dropping into the molten pool. The distribution law of the coating-matrix material inside the coating was studied. Through the heat transfer between the molten material and the matrix material, the condensation and solidification process of the coating-matrix material is simulated, the temperature change in the coating area during the solidification process is analyzed, and the solidification law of the molten material is studied. The results show that the deposition time reaches 80 μs, and the content of electrode material at the bottom of the molten pool reaches 4.5%. The content of electrode material in the upper region of the material gushing out of the molten pool is higher than that in the bottom region. The material outside the molten pool solidifies first, and the molten material in the molten pool gradually solidifies from the bottom up; the shape of the solidification interface is similar to the boundary of the molten pool. Through the single-point deposition experiment of electro-spark deposition, the surface morphology of the deposition point was observed. The depth of the concave part of the contour can reach 16 μm. The difference between the two contour curves in the horizontal direction is not much; the error of the diameter is about 4%. The element distribution of the surface and the section of the deposition point are analyzed. The diffusion distance in the depth direction of the coating is about 4μm, and the transverse diffusion distance inside the coating is 364 μm. The error is 7.6% compared with the experimental results. The cross-section structure of the deposition point was observed, and the error between the experimental results and the simulation results in diameter is about 11%. It was found that the material distribution in the sedimentary area is basically consistent with the simulation results, and the simulation results are verified from the side.

Research on Simulation of Coating Fusion and Solidification Process in Electro-Spark Deposition

Accelerated Electrospark Deposition and the Wear Behavior of Coatings

Multi-scale Simulation of Dendrite Growth for Direct Energy Deposition of Nickel-Based Superalloys

Finite Element Numerical Simulation of EDM Surface Strengthening in Gas Medium of Stainless Steel 1Cr13

An Experimental Study on Deposition Mechanism of High-Speed Spraying Cu Coating Based on Electromagnetic Pulse Welding Technology

Electro-spark Deposition of Fe-based Amorphous Alloy Coatings

Defect Control of Electro-spark Deposition WC–Co Coatings Via Adjusting Pulse Energy and Deposited Layer Number

RESEARCH STATUS OF THE ELECTRO SPARK DEPOSITION

Deposition Process and Interface Properties of Electro-Thermal Explosion Sprayed WC/Co Coating

Simulation and experimental research on nickel-based coating prepared by jet electrodeposition at different scanning speeds

Simulation of the Cold Spray Particle Deposition Process

Insight into Droplet Formation in Electroslag Remelting Process by Numerical Simulation

Droplet Formation and Dripping Behavior During the Electroslag Remelting Process with Two Series-Connected Electrodes

Mass Transfer Trends of AlCoCrFeNi High-Entropy Alloy Coatings on TC11 Substrate Via Electrospark − Computer Numerical Control Deposition

Research on Droplet Formation and Dripping Behavior During the Electroslag Remelting Process

Parameters Optimization for Electrophoretic Deposition of Mn1.5Co1.5O4 on Ferritic Stainless Steel Based on Multi-Physical Simulation

Micro EDM Deposition in Air by Single Discharge Thermo Simulation

Numerical simulation of nanoparticle pattern fabricated by electrostatic spray deposition

Simulation research on the laser electrochemical compound deposition process based on electric coupling with temperature and flow field

Numerical Simulation of Chemical Vapor Deposition Process for Fabrication of SiC Coating

Simulation of microstructure evolution in fused-coating additive manufacturing based on phase field approach