Abstract:As a surface-strengthening technology, electro-spark deposition (ESD) is widely used in the strengthening and repair of key components of high-end equipment. In this paper, a fusion and solidification model of ESD coating is established. The method of heat–fluid–solid interaction is adopted to simulate the material’s flow and fusion process in the droplet dropping into the molten pool. The distribution law of the coating-matrix material inside the coating was studied. Through the heat transfer between the molten material and the matrix material, the condensation and solidification process of the coating-matrix material is simulated, the temperature change in the coating area during the solidification process is analyzed, and the solidification law of the molten material is studied. The results show that the deposition time reaches 80 μs, and the content of electrode material at the bottom of the molten pool reaches 4.5%. The content of electrode material in the upper region of the material gushing out of the molten pool is higher than that in the bottom region. The material outside the molten pool solidifies first, and the molten material in the molten pool gradually solidifies from the bottom up; the shape of the solidification interface is similar to the boundary of the molten pool. Through the single-point deposition experiment of electro-spark deposition, the surface morphology of the deposition point was observed. The depth of the concave part of the contour can reach 16 μm. The difference between the two contour curves in the horizontal direction is not much; the error of the diameter is about 4%. The element distribution of the surface and the section of the deposition point are analyzed. The diffusion distance in the depth direction of the coating is about 4μm, and the transverse diffusion distance inside the coating is 364 μm. The error is 7.6% compared with the experimental results. The cross-section structure of the deposition point was observed, and the error between the experimental results and the simulation results in diameter is about 11%. It was found that the material distribution in the sedimentary area is basically consistent with the simulation results, and the simulation results are verified from the side.

Accelerated Electrospark Deposition and the Wear Behavior of Coatings

Features of Electrospark Coatings Formation on a Chromium Substrate Using Ceramic ZrSi2-MoSi2-ZrB2 and HfSi2-MoSi2-HfB2 Electrodes

Defect Control of Electro-spark Deposition WC–Co Coatings Via Adjusting Pulse Energy and Deposited Layer Number

Improving Abrasive Wear Resistance for Steel Hardox 400 by Electro-Spark Deposition

Preparation and tribological behaviours of graphite self-lubricating coating deposited on middle carbon steel by electrospark deposition

Research on Simulation of Coating Fusion and Solidification Process in Electro-Spark Deposition

Surface Modification of 304 Stainless Steel by Electro-Spark Deposition

Surface Modification of Resistance Welding Electrode by Electro-Spark Deposited Composite Coatings: Part I. Coating Characterization

Improving Surface Properties of Titanium Alloys by Electrospark Deposition with Low Pulse Energy

Wear Characteristics of Spheroidal Graphite Roll WC-8Co Coating Produced by Electro-Spark Deposition

Influence of Electrospark Deposition Processes on Thickness of TiC Deposition Coating

Mass Transfer Trends of AlCoCrFeNi High-Entropy Alloy Coatings on TC11 Substrate Via Electrospark − Computer Numerical Control Deposition

Research Progress in Electrospark Deposition Coatings on Titanium Alloy Surfaces: A Short Review

The effect of electrospark deposition using zirconium electrodes on structure and properties of nickel-containing alloy obtained selective laser melting

Study of Electrospark Strengthening and Erosion Behavior of 2Cr13 Stainless Steel Surface

Enhanced Discharge and Surface Properties of TiSiCN Coatings Deposited by Pulse-Enhanced Vacuum Arc Evaporation

Experimental analysis of surface integrity in electro-discharge coating process

Cucr1 Alloy Surface Hardening Via Ultrasonic Assisted Electro-Spark Deposition

Microstructure and Properties of Sparking Deposited Composite Coating on Electrode Surface

Research on iron-based amorphous alloy coated by electrospark processing and its properties

RESEARCH STATUS OF THE ELECTRO SPARK DEPOSITION