How the Test Setup Can Affect Single Fiber Tensile Testing

Marko Žižek,Caterina Czibula,Ulrich Hirn

DOI: https://doi.org/10.1080/15440478.2024.2328264

2024-03-16

Journal of Natural Fibers

Abstract:Tensile testing is the most common method to investigate natural fibers. The fibers' mechanical behavior can be considered non-linear and is influenced by viscoelasticity, plasticity, and environmental conditions. Very often such fibers are tested by gluing them with an adhesive onto a sample holder. Such a system consisting of a polymeric sample holder, adhesive, and natural fiber is complex and there is a risk that the mechanical response measured is a mix of the different contributions of those components. In this work, the key components for tensile testing of natural fibers ‒ sample holder and adhesive ‒ are investigated, to determine their influence on the measurement results. In order to isolate the influence of the measurement setup, the natural fiber is replaced with a platinum wire, which is purely linear-elastic. Hence all non-linear contributions from sample holder or adhesive can be identified. The main influence factor on the results was the glue used for fixating the fiber on the sample holder. Epoxy resin was found to be best suited. Taking these findings into account, a series of tensile tests was performed on cellulose-based natural fibers for demonstration but is applicable to any natural fiber. 拉伸试验是研究天然纤维最常见的方法. 纤维的力学行为可以被认为是非线性的,并受到粘弹性、塑性和环境条件的影响. 这种纤维通常通过用粘合剂将它们粘合到样品支架上来进行测试. 这种由聚合物样品支架、粘合剂和天然纤维组成的系统是复杂的,并且存在测量的机械响应是这些成分的不同贡献的混合的风险. 在这项工作中,研究了天然纤维拉伸测试的关键部件——样品支架和粘合剂,以确定它们对测量结果的影响. 为了隔离测量设置的影响,天然纤维被纯线性弹性的铂丝取代. 因此,可以识别来自样品支架或粘合剂的所有非线性. 影响结果的主要因素是用于将纤维固定在样品支架上的胶水. 发现环氧树脂最适合. 考虑到这些发现,对纤维素基天然纤维进行了一系列拉伸试验以进行证明,但适用于任何天然纤维.

materials science, textiles

What problem does this paper attempt to address?

The paper primarily explores how the testing apparatus affects the tensile test results of a single fiber. Specifically, the study focuses on how the sample holder and adhesive influence the final measurement results during fiber tensile testing.

The research background indicates that tensile testing is one of the most commonly used methods to study the mechanical properties of natural fibers. The mechanical behavior of natural fibers is nonlinear, influenced by viscoelasticity, plasticity, and environmental conditions. In experiments, natural fibers are usually fixed on the sample holder using adhesives for testing. This system, composed of a polymer sample holder, adhesive, and natural fiber, is very complex, so the measured mechanical response may include the combined effects of all three components.

To address this issue, the researchers designed a validation procedure, first using platinum wire instead of natural fibers as the test object, because platinum wire has purely linear elastic characteristics. This approach eliminates the interference of the fiber's own nonlinear behavior, allowing the evaluation of the sample holder and adhesive's impact on the test results. Through this simplified method, the researchers could identify the nonlinear effects brought by the sample holder or adhesive.

The study also explored the impact of different types of adhesives (such as nail polish, super glue, two-component epoxy resin, etc.) and sample holder materials (polymethyl methacrylate, i.e., PMMA or acrylic glass) on the test results. Experimental results showed that epoxy resin is the most suitable adhesive for fixing fibers, as it provides the best bonding effect without causing slippage. Additionally, the sample holder needs sufficient time to adapt to changes in relative humidity in the laboratory environment to reduce its own shrinkage's impact on the test results.

Finally, the researchers conducted tensile tests on natural fibers (such as cellulose-based fibers) using the validated sample holder system to demonstrate its practicality. By performing a series of tensile tests on these fibers, they further proved the applicability of this sample holder system for studying various types of natural fibers.