Abstract:Tensile testing is the most common method to investigate natural fibers. The fibers' mechanical behavior can be considered non-linear and is influenced by viscoelasticity, plasticity, and environmental conditions. Very often such fibers are tested by gluing them with an adhesive onto a sample holder. Such a system consisting of a polymeric sample holder, adhesive, and natural fiber is complex and there is a risk that the mechanical response measured is a mix of the different contributions of those components. In this work, the key components for tensile testing of natural fibers ‒ sample holder and adhesive ‒ are investigated, to determine their influence on the measurement results. In order to isolate the influence of the measurement setup, the natural fiber is replaced with a platinum wire, which is purely linear-elastic. Hence all non-linear contributions from sample holder or adhesive can be identified. The main influence factor on the results was the glue used for fixating the fiber on the sample holder. Epoxy resin was found to be best suited. Taking these findings into account, a series of tensile tests was performed on cellulose-based natural fibers for demonstration but is applicable to any natural fiber. 拉伸试验是研究天然纤维最常见的方法. 纤维的力学行为可以被认为是非线性的,并受到粘弹性、塑性和环境条件的影响. 这种纤维通常通过用粘合剂将它们粘合到样品支架上来进行测试. 这种由聚合物样品支架、粘合剂和天然纤维组成的系统是复杂的,并且存在测量的机械响应是这些成分的不同贡献的混合的风险. 在这项工作中,研究了天然纤维拉伸测试的关键部件——样品支架和粘合剂,以确定它们对测量结果的影响. 为了隔离测量设置的影响,天然纤维被纯线性弹性的铂丝取代. 因此,可以识别来自样品支架或粘合剂的所有非线性. 影响结果的主要因素是用于将纤维固定在样品支架上的胶水. 发现环氧树脂最适合. 考虑到这些发现,对纤维素基天然纤维进行了一系列拉伸试验以进行证明,但适用于任何天然纤维.

Fiber Arrangement Characteristics and Their Effects on Nonwoven Tensile Behavior

Effects of Fiber Shape on Mechanical Properties of Fiber Assemblies

Finite Element Modelling for Tensile Behaviour of Thermally Bonded Nonwoven Fabric

The Effect Of Pore Size Deformation On Multi-Pore Model Of Woven Geotextiles In Tension Test

Predicting the Mechanical Properties of Nonwoven Geotextiles with the Finite Element Method

Dynamic Tensile Behavior of Fiber Reinforced Materials Based on Fiber Layering Modeling

Experimental investigation on the effects of fabric architectures on mechanical and damage behaviors of carbon/epoxy woven composites

Computer Simulation of Mechanical Properties of Nonwoven Geotextiles in Soil-Fabric Interaction

Comparative studies on the effect of fabric structure on mechanical properties of carbon fiber/epoxy composites

Effect of fiber arrangement on mechanical properties of short fiber reinforced composites

Numerical investigation of the tensile behaviors of needle-punched nonwoven geotextiles

Numerical Simulation of the Mechanical Behavior of a Weft-Knitted Carbon Fiber Composite under Tensile Loading

Out-of-plane Tensile Failure Behavior of Fiber Reinforced Composites Due to Lay-Up Temperature Induced Intra-Ply and Inter-Ply Voids

A novel modeling method for the mechanical behavior of 3D woven fabrics considering yarn distortion

Role of stable‐structural yarns and fabrics on the tensile and bending performance of carbon fiber resin composites

Modeling the shear behavior of spunbond nonwoven fabrics using the finite element method

How the Test Setup Can Affect Single Fiber Tensile Testing

Analysis of the influence of yarn angle on the mechanical behaviors of cured woven composites

Theoretical Prediction of Effective Stiffness of Nonwoven Fibrous Networks with Straight and Curved Nanofibers

Modeling the Large Deformation and Microstructure Evolution of Nonwoven Polymer Fiber Networks

Modeling and characterization of the mechanical properties of nanofiber yarn