Abstract:In some traditional formative and additive manufacturing processes widely used in the fabrication of steel products, stress conditions and metallurgy typically result in a strong texture and mechanical anisotropy in both rolling high-strength low-alloy steel and additive manufacturing stainless steel products. To resolve this problem, we have investigated the effectiveness of a novel wire-arc additive manufacturing method in which the heat source is substituted by high-efficiency submerged arc plasma i.e., submerged arc additive manufacturing. An isotropic microstructure can be obtained in the bulk of large-scale low-carbon steel components by ensuring a complete columnar-to-equiaxed transition. We found that the top zone of the as-deposited component comprised columnar α-Fe grains with a typical preferential <001>α orientation. Multiple allotropic transformations were triggered by an in-situ intrinsic heat treatment (mainly the combination of multi-layer-penetration normalizing, full-layer-penetration inter-critical annealing, and long-duration tempering—i.e., NIT). Consequently, when the net bead height was no greater than the width of the fine grain zone affected by the previous layer of deposition, the microstructures in each new layer could be progressively refined and homogenized. Therefore, the intermediate zone was predominantly composed of fully equiaxed α-Fe and displayed homogeneous characteristics along the build direction. During full-layer NIT treatment, the pearlite was spheroidized slightly, reduced both in size (from 4μm to 2μm) and in area fraction (from ~5% to ~1%), thereby mitigating cracking susceptibility. Moreover, not only were the intracrystalline dislocations significantly reduced, but also their morphology evolved from tangled to movable lines. These changes, along with finer grains and the formation of high-angle grain boundaries, led to lower and more dispersed internal strain in the α-Fe matrix. Consequently, excellent Charpy toughness (over 300 J at -60 °C) with minimal deterioration in strength was achieved. Impact, tensile, and hardness tests revealed nearly isotropic mechanical characteristics. We believe that this novel method shows tremendous promise in large-scale additive manufacturing.

Features of the Lath Microstructure in the Heataffected Zone of the 09G2S Steel After Manual Arc Surfacing

Structural Features of a Heat Affected Zone with Pulsed Arc Surfacing of Railway Crossovers

Overlapping Features and Microstructures of Coarse Grain Heat-Affected Zones in Swing Arc Narrow Gap GMA Welded EH40 Grade Steels

A Novel Method for the Development of a Low-Temperature Bainitic Microstructure in the Surface Layer of Low-Carbon Steel

Submerged arc additive manufacturing (SAAM) of low-carbon steel: Effect of in-situ intrinsic heat treatment (IHT) on microstructure and mechanical properties

Microstructure and Mechanical Properties of Simulated Unaltered Coarse Grained Heat Affected Zones of 10crni3mov Steel by Double-Sided Double Arc Welding

In Situ Observation of Kinetic Processes of Lath Bainite Nucleation and Growth by Laser Scanning Confocal Microscope in Reheated Weld Metals

Microstructural Features of Low-Alloy Pipeline Steels that Determine Impact Strength of Welded Joint Heat-Affected Zone

Transition Zone Structure in the Fast-Cutting Surfaced Layer – Substrate System

Grain Refinement in the Coarse-Grained Region of the Heat-Affected Zone in Low-Carbon High-Strength Microalloyed Steels

Mechanism of Interfacial Microstructure Evolution of G115 Steel in Simulated Heat Affected Zone

Study on Laser Welded Heat-Affected Zone in New Ultralow Carbon Bainitic Steel

Microstructural Analysis of Weld Metal Microstructures in a Low Carbon High Strength Microalloyed Steel

In Situ Observation and Electron Backscattered Diffraction Analysis of Granular Bainite in Simulated Heat-Affected Zone of High-Strength Low-Alloy Steel

Producing superfine low-carbon bainitic structure through a new combined thermo-mechanical process

Role of nano-bainite laths and nanosized precipitates: Strengthening a low-alloy steel to 1870 MPa

Isothermal Transformation, Microstructure and Mechanical Properties of Ausformed Low-Carbon Carbide-Free Bainitic Steel

Wear Property of Low-Temperature Bainite in the Surface Layer of a Carburized Low Carbon Steel

Functional grading of low alloy steel to 316 L by Wire Arc Additive Manufacturing – Microstructural and mechanical characterization of bi-metal interface

Preparation and microstructural characterization of hard bainite in surface layer of low-carbon alloy steel

A Novel Process to Obtain Lamella Structured Low-Carbon Steel with Bimodal Grain Size Distribution for Potentially Improving Mechanical Property