Abstract:Abstract The solidified microstructure and carbide precipitation behavior in an S390 high-speed steel processed by electron beam melting (EBM) have been fully characterized. The as-EBM microstructure consists of discontinuous network of very fine primary carbides dispersed in auto-tempered martensite matrix together with a limited amount of retained austenite. The carbide network consists of M 2 C/M 6 C and MC carbides. Both the columnar and near-equiaxed grain structures were found in as-EBM microstructure and the presence of inter-dendritic eutectic carbides assisted in revealing the dendritic solidification nature. The top-layer microstructure observation confirmed that the columnar dendritic structured grains were located adjacent to the micro-melt pool boundary, indicating an epitaxial growth with the average growth direction parallel to the maximum thermal gradient. At the center of the micro-melt pool, the near-equiaxed grains were developed by dendritic growth parallel to the beam traveling direction. The carbide decomposition was revealed by scanning transmission electron microscopy and confirmed by transmission Kikuchi diffraction. The MC carbides (rich in V followed by W) nucleated at the interface between M 2 C (W, Fe, Mo, and Co in the order of significance) and the matrix and then grew from the outside inward, but their nucleation might occur from the M 2 C carbide itself. The thermal effect induced by the adjacent scan lines seems to trigger a solid-state phase transformation of MC → M 2 C + γ -Fe. The elemental migration was theoretically calculated and compared with the experimental results. The high hardness of ~ 65 HRC and good transverse rupture strength of ~ 2500 MPa in as-EBM S390 means that EBM processing can be used to fabricate highly alloyed tool steels. With the help of the post-processing heat treatment, the best Rockwell hardness of 73.1±0.2 HRC and transverse rupture strength of 3012±34 MPa can be obtained.

Transition Zone Structure in the Fast-Cutting Surfaced Layer – Substrate System

Structure and Properties of Surfacing Made of High-Entropy High-Speed Steel

Modification of Structure and Properties of Surfacing of High-Speed Steel by Electron-Beam Treatment

Structural-Phase State and Fracture of a Low-Carbon Steel Coating

Structural Features of a Heat Affected Zone with Pulsed Arc Surfacing of Railway Crossovers

Features of the Lath Microstructure in the Heataffected Zone of the 09G2S Steel After Manual Arc Surfacing

Effect of the Cooling Rate on Phase Transformations in a Surface-Alloyed Layer of Steel

A Coupled EBSD/TEM Analysis of the Microstructure Evolution of a Gradient Nanostructured Ferritic/Martensitic Steel Subjected to Surface Mechanical Attrition Treatment

Electron Microscopy of High-Speed Steel/30HGSA Steel Interface

Microstructure of Transition Zone in 2cr13 Steel by Laser Surface Remelting

Microstructures and phase formations in the surface layer of an AISI D2 steel treated with pulsed electron beam

Cascading phase transformations in situ for the simulated coarse-grained heat-affected zone of P92 heat-resistant steel

An In Situ Synchrotron Dilatometry and Atomistic Study of Martensite and Carbide Formation during Partitioning and Tempering

Effect of Tempering on Structure and Properties of Plasma Surfacing of R2M9U High-Speed Tool Steel

In Situ Observation of Phase Transformation and Structure Evolution of a 12 Pct Cr Ferritic Stainless Steel

On the spheroidized carbide dissolution and elemental partitioning in a high carbon bearing steel 100Cr6

Rapid Solidification Microstructure and Carbide Precipitation Behavior in Electron Beam Melted High-Speed Steel

Microstructure Transformation on Pre-Quenched and Ultrafast-Tempered High-Strength Multiphase Steels

Phase Structure and Fine Microstructure of In-Situ Vanadium Carbides in Cast High-Vanadium High-Speed Steel

Surface Integrity of Carbon Steel under Three Heat Treatment States Subjected to Orthogonal Turning Process

Microstructure in Worn Surface of Hadfield Steel Crossing