Abstract:Powder bed fusion (PBF) is an additive manufacturing technique capable of fabricating highly complex, individualised, and lightweight polymer components. However, to maximise the potential of PBF, in terms of both economic efficiency and environmental sustainability, a successful powder re-use strategy is essential. During a build, ageing and degradation processes affect the re-usability of un-sintered powder, so used powder is usually refreshed with virgin material before re-use. This study considers the effectiveness of using a 70:30 refresh ratio in a specific PBF technique: laser sintering (LS). Across a total of seven printing cycles, polyamide-12 (PA-12) powder refreshed with 30% virgin material after each build, revealed a 4.5°C increase in melting temperature. There was also a 20% reduction in particle flowability, which may be related to the presence of fine satellite particles and considerable particle cracking. This deterioration in powder quality resulted in a 5.8% increase in total part porosity, and an 11% reduction in the ultimate tensile strength of fabricated parts, over the seven build cycles. A Pearson correlation test quantified that the reduction in powder flowability was the most significant (p-value of 0.005) cause for the loss of part strength; emphasising that the revolution powder analyser could be a useful complimentary technique for determining the quality of used powder within laser sintering. Nonetheless, compared to previous studies which re-used 100% aged PA-12 powder, without refreshing with any virgin material, the observed reduction in part strength is relatively modest. This suggests that a 70:30 refresh ratio offers a good compromise between maintaining part performance, particularly for non-critical applications, without having to add an unnecessary amount of virgin powder. Therefore, this study reveals the relationship between the deterioration of powder properties and reductions in part strength; yet highlights the benefits of operating with a 70:30 refresh ratio when re-using PA-12 powder across multiple build cycles.

Processing recycled silicone powder in liquid silicone rubber injection molding and its influence on mechanical properties

Mortar with Substituted Recycled PET Powder: Experimental Characterization and Data-Driven Strength Predictive Models

A review of liquid silicone rubber injection molding: Process variables and process modeling

Liquid Silicone Rubber Foams Made with Water as Blowing Agent

Effect of Preprocessing Temperature On the Recycling of Waste Direct Metal Laser Sintering Powder

Analysis and Optimization of the Silicone Molding Process Based on Numerical Simulations and Experiments

Numerical investigation on the reuse of recycled powders in powder bed fusion additive manufacturing

Looking over liquid silicone rubbers: (1) network topology vs chemical formulations

Re-use of polyamide-12 in powder bed fusion and its effect on process-relevant powder characteristics and final part properties

Maraging steel powder recycling effect on the tensile and fatigue behavior of parts produced through the laser powder bed fusion (L-PBF) process

Preparation and characterization of red mud/liquid silicon rubber with good thermal‐stability and processability

Processing Biodegradable Fused Filament Fabrication Waste with Micro-Silica Particles

Mechanochemical reclaiming and thermoplastic re-processing of waste Acrylonitrile-butadiene rubber (NBR)/poly (Vinyl Chloride) (PVC) insulation materials

Predictive Modeling of Mechanical Properties from Degraded Polyamide 12 Powder in Laser Powder Bed Fusion

Hybrid Chemomechanical Plastics Recycling: Solvent-free, High-Speed Reactive Extrusion of Low-Density Polyethylene

Recycling Development And Shaping Of A Thermo-Reversible Epoxy Resin With Partial Contents Of Diels-Alder Bonds

Recycled sand for sustainable 3D-printed sand mold processes

MC-Injection Molding with Liquid Silicone Rubber (LSR) and Acrylonitrile Butadiene Styrene (ABS) for Medical Technology

In‐mold rheology and automated process control for injection molding of recycled polypropylene

A technical review of the challenges of powder recycling in the laser powder bed fusion additive manufacturing process

Investigation of anisotropic shrinkage in liquid silicone rubber injection molding: Process variables