Abstract:Powder bed fusion (PBF) is an additive manufacturing technique capable of fabricating highly complex, individualised, and lightweight polymer components. However, to maximise the potential of PBF, in terms of both economic efficiency and environmental sustainability, a successful powder re-use strategy is essential. During a build, ageing and degradation processes affect the re-usability of un-sintered powder, so used powder is usually refreshed with virgin material before re-use. This study considers the effectiveness of using a 70:30 refresh ratio in a specific PBF technique: laser sintering (LS). Across a total of seven printing cycles, polyamide-12 (PA-12) powder refreshed with 30% virgin material after each build, revealed a 4.5°C increase in melting temperature. There was also a 20% reduction in particle flowability, which may be related to the presence of fine satellite particles and considerable particle cracking. This deterioration in powder quality resulted in a 5.8% increase in total part porosity, and an 11% reduction in the ultimate tensile strength of fabricated parts, over the seven build cycles. A Pearson correlation test quantified that the reduction in powder flowability was the most significant (p-value of 0.005) cause for the loss of part strength; emphasising that the revolution powder analyser could be a useful complimentary technique for determining the quality of used powder within laser sintering. Nonetheless, compared to previous studies which re-used 100% aged PA-12 powder, without refreshing with any virgin material, the observed reduction in part strength is relatively modest. This suggests that a 70:30 refresh ratio offers a good compromise between maintaining part performance, particularly for non-critical applications, without having to add an unnecessary amount of virgin powder. Therefore, this study reveals the relationship between the deterioration of powder properties and reductions in part strength; yet highlights the benefits of operating with a 70:30 refresh ratio when re-using PA-12 powder across multiple build cycles.

Predictive Modeling of Mechanical Properties from Degraded Polyamide 12 Powder in Laser Powder Bed Fusion

Re-use of polyamide-12 in powder bed fusion and its effect on process-relevant powder characteristics and final part properties

The Effect of Powder Re-Use on the Coalescence Behaviour and Isothermal Crystallisation Kinetics of Polyamide 12 within Powder Bed Fusion

New powder reuse schema in laser-based powder bed fusion of polymers

Optimization of Mechanical Properties and Evaluation of Fatigue Behavior of Selective Laser Sintered Polyamide-12 Components

Mechanical Testing of Selective-Laser-Sintered Polyamide PA2200 Details: Analysis of Tensile Properties via Finite Element Method and Machine Learning Approaches

Recovery of residual polyamide (PA12) from polymer powder bed fusion additive manufacturing process through a binder jetting process

Towards the Reuse of Fire Retarded Polyamide 12 for Laser Sintering

Numerical Model and Experimental Validation for Laser Sinterable Semi-Crystalline Polymer: Shrinkage and Warping

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

On the Difference in Mechanical Behavior of Glass Bead-Filled Polyamide 12 Specimens Produced by Laser Sintering and Injection Molding

Additive manufacturing of a polyamide 12 and silica nanocomposite: A route for the reusability of a thermoplastic selective laser sintering powder

Effect of Powder Recycling on Hardness and Impact Toughness of Polyamide Formed by Selective Laser Sintering

Characterisation and prediction of mechanical properties in laser powder bed fusion-printed parts: a comparative analysis using machine learning

Process Prediction of Selective Laser Sintering Based on Heat Transfer Analysis for Polyamide Composite Powders

Additive Manufacturing of Polyamide 66: Effect of Process Parameters on Crystallinity and Mechanical Properties

Effects of laser sintering processing time and temperature on changes in polyamide 12 powder particle size, shape and distribution

Multiphysics modelling of powder bed fusion for polymers

Maraging steel powder recycling effect on the tensile and fatigue behavior of parts produced through the laser powder bed fusion (L-PBF) process

Melting process and mechanics on laser sintering of single layer polyamide 6 powder

Systematical Mechanism of Polyamide-12 Aging and Its Micro-Structural Evolution During Laser Sintering